HISENSE 40N2179PW LED TV NAND DUMP FREE
TP.MS6486.PB756
HISENSE 40N2179PW LED TV
Hisense 40N2179PW LED TV NAND dump file is shared for repairing purpose. If the Hisense 40N2179PW LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then NAND dump file can be loaded. If the Hisense 40N2179PW LED TV is dead. Mean no power no indication light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.
If both are found ok and Hisense 40N2179PW LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load NAND dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the Hisense 40N2179PW LED TV are tested and found accurate then write NAND dump file because it seems to be a software problem. I hope the issue will be resolved by rewriting NAND memory.
Installation Instructions:
For writing NAND dump file in Hisense 40N2179PW LED TV board, first of all save the backup of old Nand data then erase the NAND chip to clear any bad sector. After it write the given Hisense 40N2179PW LED TV NAND dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the NAND dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.
Technical Specifications Hisense 40N2179PW LED TV:
- Make/Brand: Hisense
- Main Board/Chassis: TP.MS6486.PB756
- Panel Info:JHD396N2F01-BS
- Main Processor/Chipset: MSD6486
- NAND: TH58NVG2S3HTА00
- Firmware Type: NAND Backup
- Product User: Hisense
- Product Model: 40N2179PW
Special Note:
The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the NAND Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in case of any damage/loss.
About Mainboard:
Hisense 40N2179PW LED TV dump file is shared below for repairing the firmware problem. Hisense 40N2179PW LED TV has the main board TP.MS6486.PB756 installed in it so the NAND memory file backup saved from working board TP.MS6486.PB756. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS6486.PB756 dump file is shared below for the Hisense 40N2179PW LED TV repairing.
- A Hisense 40N2179PW-NAND-DUMP.part1
- B Hisense 40N2179PW-NAND-DUMP.part2
- C Hisense 40N2179PW-NAND-DUMP.part3
How to Download Free Software for Hisense 40N2179PW LED TV:
1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done
