SONY KDL-32S2030 LED TV flash dump file is shared for repairing purpose. If the SONY KDL-32S2030 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded.

SONY KDL-32S2030

Troubleshooting Guide:

If the SONY KDL-32S2030 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SONY KDL-32S2030 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SONY KDL-32S2030 LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing flash dump file in SONY KDL-32S2030 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SONY KDL-32S2030 LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SONY KDL-32S2030 LED TV:
  • Make/Brand: SONY
  • Main Board/Chassis: KDL-32S2030
  • Board Type:
  • Power Source:
  • Rated Power Consumption:
  • Panel Info:
  • T-CON:
  • Screen Resolution:
  • Main Processor/Chipset:
  • SPI Flash:
  • Tuner:
  • Firmware Type: SPI Dump
  • Product User: SONY
  • Product Model:
  • Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Flash Dumps TV

About Mainboard:

SONY KDL-32S2030 LED TV dump file is shared below for repairing the firmware problem. SONY KDL-32S2030 LED TV has the main board KDL-32S2030 installed in it so the SPI Flash file backup saved from working board KDL-32S2030. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. KDL-32S2030 dump file is shared below for the SONY KDL-32S2030 LED TV repairing.

SONY KDL-32S2030

How to Download Free Software for SONY KDL-32S2030 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly