AIWA Software Free Download

13/02/2023
0 26

AIWA 19LE6010 LED TV FLASH DUMP
Download Here

AIWA 19LE6010 LED TV

AIWA 19LE6010 LED TV Software file is shared for repairing purpose. If the AIWA 19LE6010 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 19LE6010 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 19LE6010 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 19LE6010 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 19LE6010 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 19LE6010 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 19LE6010 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: V1N09; V1L11
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: V185J1-LE1 Rev.C1
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 19LE6010 LED TV dump file is shared below for repairing the firmware problem. AIWA 19LE6010 LED TV has the main board V1N09; V1L11 installed in it so the SPI Flash file backup saved from working board V1N09; V1L11. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. V1N09; V1L11 dump file is shared below for the AIWA 19LE6010 LED TV repairing.

AIWA 19LE6010 LED TV Software download free.

How to Download Free Software for AIWA 19LE6010 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 141

AIWA 20LE7011 LED TV FLASH DUMP
Download Here

AIWA 20LE7011 LED TV

AIWA 20LE7011 LED TV Software file is shared for repairing purpose. If the AIWA 20LE7011 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 20LE7011 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 20LE7011 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 20LE7011 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 20LE7011 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 20LE7011 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 20LE7011 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: CV59L-A23
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: M195FGE-P03
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 20LE7011 LED TV dump file is shared below for repairing the firmware problem. AIWA 20LE7011 LED TV has the main board CV59L-A23 installed in it so the SPI Flash file backup saved from working board CV59L-A23. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV59L-A23 dump file is shared below for the AIWA 20LE7011 LED TV repairing.

AIWA 20LE7011 LED TV Software download free.

How to Download Free Software for AIWA 20LE7011 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 16

AIWA 20LE7010 LED TV FLASH DUMP
Download Here

AIWA 20LE7010 LED TV

AIWA 20LE7010 LED TV Software file is shared for repairing purpose. If the AIWA 20LE7010 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 20LE7010 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 20LE7010 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 20LE7010 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 20LE7010 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 20LE7010 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 20LE7010 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: CV59L-A23
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: HK195WLEDM-CH05H
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 20LE7010 LED TV dump file is shared below for repairing the firmware problem. AIWA 20LE7010 LED TV has the main board CV59L-A23 installed in it so the SPI Flash file backup saved from working board CV59L-A23. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV59L-A23 dump file is shared below for the AIWA 20LE7010 LED TV repairing.

AIWA 20LE7010 LED TV Software download free.

How to Download Free Software for AIWA 20LE7010 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 18

AIWA 32LE7020 LED TV FLASH DUMP
Download Here

AIWA 32LE7020 LED TV

AIWA 32LE7020 LED TV Software file is shared for repairing purpose. If the AIWA 32LE7020 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 32LE7020 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 32LE7020 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 32LE7020 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 32LE7020 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 32LE7020 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 32LE7020 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: 5800-A6M31G-0P10 VER:00.0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LC320DXJ(SH)(A2)
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 32LE7020 LED TV dump file is shared below for repairing the firmware problem. AIWA 32LE7020 LED TV has the main board 5800-A6M31G-0P10 VER:00.0 installed in it so the SPI Flash file backup saved from working board 5800-A6M31G-0P10 VER:00.0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 5800-A6M31G-0P10 VER:00.0 dump file is shared below for the AIWA 32LE7020 LED TV repairing.

AIWA 32LE7020 LED TV Software download free.

How to Download Free Software for AIWA 32LE7020 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 21

AIWA 32LE4020 LED TV FLASH DUMP
Download Here

AIWA 32LE4020 LED TV

AIWA 32LE4020 LED TV Software file is shared for repairing purpose. If the AIWA 32LE4020 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 32LE4020 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 32LE4020 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 32LE4020 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 32LE4020 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 32LE4020 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 32LE4020 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: 5800-A6M31G-0P10 Ver.00.01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LC320DXJ-SHA2 GDL320HY
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 32LE4020 LED TV dump file is shared below for repairing the firmware problem. AIWA 32LE4020 LED TV has the main board 5800-A6M31G-0P10 Ver.00.01 installed in it so the SPI Flash file backup saved from working board 5800-A6M31G-0P10 Ver.00.01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 5800-A6M31G-0P10 Ver.00.01 dump file is shared below for the AIWA 32LE4020 LED TV repairing.

AIWA 32LE4020 LED TV Software download free.

How to Download Free Software for AIWA 32LE4020 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 18

AIWA 22LE5020 LED TV FLASH DUMP
Download Here

AIWA 22LE5020 LED TV

AIWA 22LE5020 LED TV Software file is shared for repairing purpose. If the AIWA 22LE5020 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 22LE5020 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 22LE5020 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 22LE5020 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 22LE5020 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 22LE5020 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 22LE5020 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: 5800-A6M35G-0P30 Ver: V1R07
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LC215DU2A
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 22LE5020 LED TV dump file is shared below for repairing the firmware problem. AIWA 22LE5020 LED TV has the main board 5800-A6M35G-0P30 Ver: V1R07 installed in it so the SPI Flash file backup saved from working board 5800-A6M35G-0P30 Ver: V1R07. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 5800-A6M35G-0P30 Ver: V1R07 dump file is shared below for the AIWA 22LE5020 LED TV repairing.

AIWA 22LE5020 LED TV Software download free.

How to Download Free Software for AIWA 22LE5020 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 45

AIWA 40LE5120 LED TV FLASH DUMP
Download Here

AIWA 40LE5120 LED TV

AIWA 40LE5120 LED TV Software file is shared for repairing purpose. If the AIWA 40LE5120 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 40LE5120 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 40LE5120 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 40LE5120 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 40LE5120 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 40LE5120 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 40LE5120 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: 5800-A6M32G-0P10
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: RDL400FY(QDO-400)
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 40LE5120 LED TV dump file is shared below for repairing the firmware problem. AIWA 40LE5120 LED TV has the main board 5800-A6M32G-0P10 installed in it so the SPI Flash file backup saved from working board 5800-A6M32G-0P10. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 5800-A6M32G-0P10 dump file is shared below for the AIWA 40LE5120 LED TV repairing.

AIWA 40LE5120 LED TV Software download free.

How to Download Free Software for AIWA 40LE5120 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 15

AIWA 40LE4120 LED TV FLASH DUMP
Download Here

AIWA 40LE4120 LED TV

AIWA 40LE4120 LED TV Software file is shared for repairing purpose. If the AIWA 40LE4120 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA 40LE4120 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA 40LE4120 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA 40LE4120 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA 40LE4120 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA 40LE4120 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA 40LE4120 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: 5800-A6M32G-0P10
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: RDL400FY
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA 40LE4120 LED TV dump file is shared below for repairing the firmware problem. AIWA 40LE4120 LED TV has the main board 5800-A6M32G-0P10 installed in it so the SPI Flash file backup saved from working board 5800-A6M32G-0P10. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 5800-A6M32G-0P10 dump file is shared below for the AIWA 40LE4120 LED TV repairing.

AIWA 40LE4120 LED TV Software download free.

How to Download Free Software for AIWA 40LE4120 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 683

AIWA JH32DT180N LED TV FLASH DUMP
Download Here

AIWA JH32DT180N LED TV

AIWA JH32DT180N LED TV Software file is shared for repairing purpose. If the AIWA JH32DT180N LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA JH32DT180N LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA JH32DT180N LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA JH32DT180N LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA JH32DT180N LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA JH32DT180N LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA JH32DT180N LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: TP.MS3663S.PB818
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: HV320WHB-NXX
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA JH32DT180N LED TV dump file is shared below for repairing the firmware problem. AIWA JH32DT180N LED TV has the main board TP.MS3663S.PB818 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PB818. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PB818 dump file is shared below for the AIWA JH32DT180N LED TV repairing.

AIWA JH32DT180N LED TV Software download free.

How to Download Free Software for AIWA JH32DT180N LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
13/02/2023
0 21

AIWA EU50DT200 LED TV FLASH DUMP
Download Here

AIWA EU50DT200 LED TV

AIWA EU50DT200 LED TV Software file is shared for repairing purpose. If the AIWA EU50DT200 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AIWA EU50DT200 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AIWA EU50DT200 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AIWA EU50DT200 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AIWA EU50DT200 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AIWA EU50DT200 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AIWA EU50DT200 LED TV:
- Make/Brand: AIWA
- Main Board/Chassis: TP.MS3663S.PC821
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: D50-K18 CV500U1-T01
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AIWA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AIWA EU50DT200 LED TV dump file is shared below for repairing the firmware problem. AIWA EU50DT200 LED TV has the main board TP.MS3663S.PC821 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PC821. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PC821 dump file is shared below for the AIWA EU50DT200 LED TV repairing.

AIWA EU50DT200 LED TV Software download free.

How to Download Free Software for AIWA EU50DT200 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

AIWA 19LE6010 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 19LE6010 LED TV:

About Mainboard:

AIWA 20LE7011 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 20LE7011 LED TV:

About Mainboard:

AIWA 20LE7010 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 20LE7010 LED TV:

About Mainboard:

AIWA 32LE7020 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 32LE7020 LED TV:

About Mainboard:

AIWA 32LE4020 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 32LE4020 LED TV:

About Mainboard:

AIWA 22LE5020 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 22LE5020 LED TV:

About Mainboard:

AIWA 40LE5120 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 40LE5120 LED TV:

About Mainboard:

AIWA 40LE4120 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA 40LE4120 LED TV:

About Mainboard:

AIWA JH32DT180N LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA JH32DT180N LED TV:

About Mainboard:

AIWA EU50DT200 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AIWA EU50DT200 LED TV:

About Mainboard:

Adblock Detected