AKAI Download Center

  • AKAI UA32DF2110 LED TV FLASH DUMP

    AKAI UA32DF2110 LED TV

    AKAI UA32DF2110 LED TV Software file is shared for repairing purpose. If the AKAI UA32DF2110 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI UA32DF2110

    Troubleshooting Guide:

    If the AKAI UA32DF2110 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI UA32DF2110 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI UA32DF2110 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI UA32DF2110 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI UA32DF2110 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI UA32DF2110 LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: TP.V56.PB826
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: ST3151A05-8-XC-3
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI UA32DF2110 LED TV dump file is shared below for repairing the firmware problem. AKAI UA32DF2110 LED TV has the main board TP.V56.PB826 installed in it so the SPI Flash file backup saved from working board TP.V56.PB826. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.V56.PB826 dump file is shared below for the AKAI UA32DF2110 LED TV repairing.

    Download
    AKAI UA32DF2110 LED TV Software download free.

    How to Download Free Software for AKAI UA32DF2110 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI LEA-32B49P LED TV FLASH DUMP

    AKAI LEA-32B49P LED TV

    AKAI LEA-32B49P LED TV Software file is shared for repairing purpose. If the AKAI LEA-32B49P LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI LEA-32B49P

    Troubleshooting Guide:

    If the AKAI LEA-32B49P LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI LEA-32B49P LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-32B49P LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI LEA-32B49P LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-32B49P LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI LEA-32B49P LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: MK-RE01-160714-JWB01
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: RH82-D320L13-BGY-C3 D320L12C
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI LEA-32B49P LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-32B49P LED TV has the main board MK-RE01-160714-JWB01 installed in it so the SPI Flash file backup saved from working board MK-RE01-160714-JWB01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MK-RE01-160714-JWB01 dump file is shared below for the AKAI LEA-32B49P LED TV repairing.

    Download
    AKAI LEA-32B49P LED TV Software download free.

    How to Download Free Software for AKAI LEA-32B49P LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI LEA-32X91M LED TV FLASH DUMP

    AKAI LEA-32X91M LED TV

    AKAI LEA-32X91M LED TV Software file is shared for repairing purpose. If the AKAI LEA-32X91M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI LEA-32X91M

    Troubleshooting Guide:

    If the AKAI LEA-32X91M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI LEA-32X91M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-32X91M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI LEA-32X91M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-32X91M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI LEA-32X91M LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: HK.T.S2T512CP539
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: HV320WHV-N86
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI LEA-32X91M LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-32X91M LED TV has the main board HK.T.S2T512CP539 installed in it so the SPI Flash file backup saved from working board HK.T.S2T512CP539. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.S2T512CP539 dump file is shared below for the AKAI LEA-32X91M LED TV repairing.

    Download
    AKAI LEA-32X91M LED TV Software download free.

    How to Download Free Software for AKAI LEA-32X91M LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI TVL327 LED TV FLASH DUMP

    AKAI TVL327 LED TV

    AKAI TVL327 LED TV Software file is shared for repairing purpose. If the AKAI TVL327 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI TVL327

    Troubleshooting Guide:

    If the AKAI TVL327 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI TVL327 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI TVL327 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI TVL327 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI TVL327 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI TVL327 LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: TP.SIS231.P93
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI TVL327 LED TV dump file is shared below for repairing the firmware problem. AKAI TVL327 LED TV has the main board TP.SIS231.P93 installed in it so the SPI Flash file backup saved from working board TP.SIS231.P93. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.SIS231.P93 dump file is shared below for the AKAI TVL327 LED TV repairing.

    Download
    AKAI TVL327 LED TV Software download free.

    How to Download Free Software for AKAI TVL327 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI LEA-32D102M LED TV FLASH DUMP

    AKAI LEA-32D102M LED TV

    AKAI LEA-32D102M LED TV Software file is shared for repairing purpose. If the AKAI LEA-32D102M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI LEA-32D102M

    Troubleshooting Guide:

    If the AKAI LEA-32D102M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI LEA-32D102M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-32D102M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI LEA-32D102M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-32D102M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI LEA-32D102M LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: HK.T.S2T512CP539
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: KM0320LDCH
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI LEA-32D102M LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-32D102M LED TV has the main board HK.T.S2T512CP539 installed in it so the SPI Flash file backup saved from working board HK.T.S2T512CP539. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.S2T512CP539 dump file is shared below for the AKAI LEA-32D102M LED TV repairing.

    Download
    AKAI LEA-32D102M LED TV Software download free.

    How to Download Free Software for AKAI LEA-32D102M LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI UA40LEP1T2 LED TV FLASH DUMP

    AKAI UA40LEP1T2 LED TV

    AKAI UA40LEP1T2 LED TV Software file is shared for repairing purpose. If the AKAI UA40LEP1T2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI UA40LEP1T2

    Troubleshooting Guide:

    If the AKAI UA40LEP1T2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI UA40LEP1T2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI UA40LEP1T2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI UA40LEP1T2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI UA40LEP1T2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI UA40LEP1T2 LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: P75-3663SV6.3
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: CX400DLEM
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI UA40LEP1T2 LED TV dump file is shared below for repairing the firmware problem. AKAI UA40LEP1T2 LED TV has the main board P75-3663SV6.3 installed in it so the SPI Flash file backup saved from working board P75-3663SV6.3. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. P75-3663SV6.3 dump file is shared below for the AKAI UA40LEP1T2 LED TV repairing.

    Download
    AKAI UA40LEP1T2 LED TV Software download free.

    How to Download Free Software for AKAI UA40LEP1T2 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI LEA-24D102M LED TV FLASH DUMP

    AKAI LEA-24D102M LED TV

    AKAI LEA-24D102M LED TV Software file is shared for repairing purpose. If the AKAI LEA-24D102M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI LEA-24D102M

    Troubleshooting Guide:

    If the AKAI LEA-24D102M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI LEA-24D102M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-24D102M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI LEA-24D102M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-24D102M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI LEA-24D102M LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: HK.T.S2T512CP532
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: V236BJ1-P01 Rev.CB
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI LEA-24D102M LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-24D102M LED TV has the main board HK.T.S2T512CP532 installed in it so the SPI Flash file backup saved from working board HK.T.S2T512CP532. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.S2T512CP532 dump file is shared below for the AKAI LEA-24D102M LED TV repairing.

    Download
    AKAI LEA-24D102M LED TV Software download free.

    How to Download Free Software for AKAI LEA-24D102M LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI LEA-39D102M LED TV FLASH DUMP

    AKAI LEA-39D102M LED TV

    AKAI LEA-39D102M LED TV Software file is shared for repairing purpose. If the AKAI LEA-39D102M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI LEA-39D102M

    Troubleshooting Guide:

    If the AKAI LEA-39D102M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI LEA-39D102M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-39D102M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI LEA-39D102M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-39D102M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI LEA-39D102M LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: HK.T.S2T512CP639
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: LC390TU1A
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI LEA-39D102M LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-39D102M LED TV has the main board HK.T.S2T512CP639 installed in it so the SPI Flash file backup saved from working board HK.T.S2T512CP639. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.S2T512CP639 dump file is shared below for the AKAI LEA-39D102M LED TV repairing.

    Download
    AKAI LEA-39D102M LED TV Software download free.

    How to Download Free Software for AKAI LEA-39D102M LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI UA32DF2110T2 LED TV FLASH DUMP

    AKAI UA32DF2110T2 LED TV

    AKAI UA32DF2110T2 LED TV Software file is shared for repairing purpose. If the AKAI UA32DF2110T2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI UA32DF2110T2

    Troubleshooting Guide:

    If the AKAI UA32DF2110T2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI UA32DF2110T2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI UA32DF2110T2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI UA32DF2110T2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI UA32DF2110T2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI UA32DF2110T2 LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: LDD.M3663.A48
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: E32DF2000-1
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI UA32DF2110T2 LED TV dump file is shared below for repairing the firmware problem. AKAI UA32DF2110T2 LED TV has the main board LDD.M3663.A48 installed in it so the SPI Flash file backup saved from working board LDD.M3663.A48. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LDD.M3663.A48 dump file is shared below for the AKAI UA32DF2110T2 LED TV repairing.

    Download
    AKAI UA32DF2110T2 LED TV Software download free.

    How to Download Free Software for AKAI UA32DF2110T2 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • AKAI UA39LEZ1T2 LED TV FLASH DUMP

    AKAI UA39LEZ1T2 LED TV

    AKAI UA39LEZ1T2 LED TV Software file is shared for repairing purpose. If the AKAI UA39LEZ1T2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    AKAI UA39LEZ1T2

    Troubleshooting Guide:

    If the AKAI UA39LEZ1T2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and AKAI UA39LEZ1T2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI UA39LEZ1T2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in AKAI UA39LEZ1T2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI UA39LEZ1T2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications AKAI UA39LEZ1T2 LED TV:
    • Make/Brand: AKAI
    • Main Board/Chassis: P75-3663SV6.3-A4L
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: CX39DLEM
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: AKAI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    AKAI UA39LEZ1T2 LED TV dump file is shared below for repairing the firmware problem. AKAI UA39LEZ1T2 LED TV has the main board P75-3663SV6.3-A4L installed in it so the SPI Flash file backup saved from working board P75-3663SV6.3-A4L. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. P75-3663SV6.3-A4L dump file is shared below for the AKAI UA39LEZ1T2 LED TV repairing.

    Download
    AKAI UA39LEZ1T2 LED TV Software download free.

    How to Download Free Software for AKAI UA39LEZ1T2 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly