AKIRA Download Center

23/02/2023
0 57

AKIRA 32LED01T2M LED TV FLASH DUMP
Download Here

AKIRA 32LED01T2M LED TV

AKIRA 32LED01T2M LED TV Software file is shared for repairing purpose. If the AKIRA 32LED01T2M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 32LED01T2M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 32LED01T2M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 32LED01T2M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 32LED01T2M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 32LED01T2M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 32LED01T2M LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: CV3463H-A42
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: SM315TWD602 D0206
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 32LED01T2M LED TV dump file is shared below for repairing the firmware problem. AKIRA 32LED01T2M LED TV has the main board CV3463H-A42 installed in it so the SPI Flash file backup saved from working board CV3463H-A42. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3463H-A42 dump file is shared below for the AKIRA 32LED01T2M LED TV repairing.

AKIRA 32LED01T2M LED TV Software download free.

How to Download Free Software for AKIRA 32LED01T2M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 18

AKIRA 32LED03T2M LED TV FLASH DUMP
Download Here

AKIRA 32LED03T2M LED TV

AKIRA 32LED03T2M LED TV Software file is shared for repairing purpose. If the AKIRA 32LED03T2M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 32LED03T2M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 32LED03T2M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 32LED03T2M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 32LED03T2M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 32LED03T2M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 32LED03T2M LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: CV3463H-A42
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: SM315TWD602
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 32LED03T2M LED TV dump file is shared below for repairing the firmware problem. AKIRA 32LED03T2M LED TV has the main board CV3463H-A42 installed in it so the SPI Flash file backup saved from working board CV3463H-A42. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3463H-A42 dump file is shared below for the AKIRA 32LED03T2M LED TV repairing.

AKIRA 32LED03T2M LED TV Software download free.

How to Download Free Software for AKIRA 32LED03T2M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 16

AKIRA 32LEC05T2S LED TV FLASH DUMP
Download Here

AKIRA 32LEC05T2S LED TV

AKIRA 32LEC05T2S LED TV Software file is shared for repairing purpose. If the AKIRA 32LEC05T2S LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 32LEC05T2S LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 32LEC05T2S LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 32LEC05T2S LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 32LEC05T2S LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 32LEC05T2S LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 32LEC05T2S LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: ST3151A05-8
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 32LEC05T2S LED TV dump file is shared below for repairing the firmware problem. AKIRA 32LEC05T2S LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the AKIRA 32LEC05T2S LED TV repairing.

AKIRA 32LEC05T2S LED TV Software download free.

How to Download Free Software for AKIRA 32LEC05T2S LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 21

AKIRA 32LED02T2M LED TV FLASH DUMP
Download Here

AKIRA 32LED02T2M LED TV

AKIRA 32LED02T2M LED TV Software file is shared for repairing purpose. If the AKIRA 32LED02T2M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 32LED02T2M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 32LED02T2M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 32LED02T2M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 32LED02T2M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 32LED02T2M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 32LED02T2M LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: TP.MS3463.SPB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: ST3151A04-9 Ver.2.1
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 32LED02T2M LED TV dump file is shared below for repairing the firmware problem. AKIRA 32LED02T2M LED TV has the main board TP.MS3463.SPB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463.SPB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463.SPB801 dump file is shared below for the AKIRA 32LED02T2M LED TV repairing.

AKIRA 32LED02T2M LED TV Software download free.

How to Download Free Software for AKIRA 32LED02T2M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 10

AKIRA 32LED38T2P LED TV FLASH DUMP
Download Here

AKIRA 32LED38T2P LED TV

AKIRA 32LED38T2P LED TV Software file is shared for repairing purpose. If the AKIRA 32LED38T2P LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 32LED38T2P LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 32LED38T2P LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 32LED38T2P LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 32LED38T2P LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 32LED38T2P LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 32LED38T2P LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: ST3151A05-8
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 32LED38T2P LED TV dump file is shared below for repairing the firmware problem. AKIRA 32LED38T2P LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the AKIRA 32LED38T2P LED TV repairing.

AKIRA 32LED38T2P LED TV Software download free.

How to Download Free Software for AKIRA 32LED38T2P LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 19

AKIRA 39LED01T2M LED TV FLASH DUMP
Download Here

AKIRA 39LED01T2M LED TV

AKIRA 39LED01T2M LED TV Software file is shared for repairing purpose. If the AKIRA 39LED01T2M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 39LED01T2M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 39LED01T2M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 39LED01T2M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 39LED01T2M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 39LED01T2M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 39LED01T2M LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: CV512H-U42
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LC390TA2A
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 39LED01T2M LED TV dump file is shared below for repairing the firmware problem. AKIRA 39LED01T2M LED TV has the main board CV512H-U42 installed in it so the SPI Flash file backup saved from working board CV512H-U42. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV512H-U42 dump file is shared below for the AKIRA 39LED01T2M LED TV repairing.

AKIRA 39LED01T2M LED TV Software download free.

How to Download Free Software for AKIRA 39LED01T2M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 52

AKIRA 32LED38P LED TV FLASH DUMP
Download Here

AKIRA 32LED38P LED TV

AKIRA 32LED38P LED TV Software file is shared for repairing purpose. If the AKIRA 32LED38P LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA 32LED38P LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA 32LED38P LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA 32LED38P LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA 32LED38P LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA 32LED38P LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA 32LED38P LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: TP.VST59.PB819
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: ST3151A05-8
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA 32LED38P LED TV dump file is shared below for repairing the firmware problem. AKIRA 32LED38P LED TV has the main board TP.VST59.PB819 installed in it so the SPI Flash file backup saved from working board TP.VST59.PB819. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59.PB819 dump file is shared below for the AKIRA 32LED38P LED TV repairing.

AKIRA 32LED38P LED TV Software download free.

How to Download Free Software for AKIRA 32LED38P LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 18

AKIRA LCT-32V88MMP LED TV FLASH DUMP
Download Here

AKIRA LCT-32V88MMP LED TV

AKIRA LCT-32V88MMP LED TV Software file is shared for repairing purpose. If the AKIRA LCT-32V88MMP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA LCT-32V88MMP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA LCT-32V88MMP LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA LCT-32V88MMP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA LCT-32V88MMP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA LCT-32V88MMP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA LCT-32V88MMP LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: JUG7.820.121 REV1.01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LTA320WT-L05
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA LCT-32V88MMP LED TV dump file is shared below for repairing the firmware problem. AKIRA LCT-32V88MMP LED TV has the main board JUG7.820.121 REV1.01 installed in it so the SPI Flash file backup saved from working board JUG7.820.121 REV1.01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. JUG7.820.121 REV1.01 dump file is shared below for the AKIRA LCT-32V88MMP LED TV repairing.

AKIRA LCT-32V88MMP LED TV Software download free.

How to Download Free Software for AKIRA LCT-32V88MMP LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 28

AKIRA LCT-22V82ST LED TV FLASH DUMP
Download Here

AKIRA LCT-22V82ST LED TV

AKIRA LCT-22V82ST LED TV Software file is shared for repairing purpose. If the AKIRA LCT-22V82ST LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA LCT-22V82ST LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA LCT-22V82ST LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA LCT-22V82ST LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA LCT-22V82ST LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA LCT-22V82ST LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA LCT-22V82ST LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: HK-7100-V6.55
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LM220WE1-TLD1
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA LCT-22V82ST LED TV dump file is shared below for repairing the firmware problem. AKIRA LCT-22V82ST LED TV has the main board HK-7100-V6.55 installed in it so the SPI Flash file backup saved from working board HK-7100-V6.55. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-7100-V6.55 dump file is shared below for the AKIRA LCT-22V82ST LED TV repairing.

AKIRA LCT-22V82ST LED TV Software download free.

How to Download Free Software for AKIRA LCT-22V82ST LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/02/2023
0 99

AKIRA LCT-47CH19ST LED TV FLASH DUMP
Download Here

AKIRA LCT-47CH19ST LED TV

AKIRA LCT-47CH19ST LED TV Software file is shared for repairing purpose. If the AKIRA LCT-47CH19ST LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKIRA LCT-47CH19ST LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKIRA LCT-47CH19ST LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKIRA LCT-47CH19ST LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKIRA LCT-47CH19ST LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKIRA LCT-47CH19ST LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKIRA LCT-47CH19ST LED TV:
- Make/Brand: AKIRA
- Main Board/Chassis: JUG.7.820.265 Ver1.00
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LC470WU4
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKIRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKIRA LCT-47CH19ST LED TV dump file is shared below for repairing the firmware problem. AKIRA LCT-47CH19ST LED TV has the main board JUG.7.820.265 Ver1.00 installed in it so the SPI Flash file backup saved from working board JUG.7.820.265 Ver1.00. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. JUG.7.820.265 Ver1.00 dump file is shared below for the AKIRA LCT-47CH19ST LED TV repairing.

AKIRA LCT-47CH19ST LED TV Software download free.

How to Download Free Software for AKIRA LCT-47CH19ST LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

AKIRA 32LED01T2M LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 32LED01T2M LED TV:

About Mainboard:

AKIRA 32LED03T2M LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 32LED03T2M LED TV:

About Mainboard:

AKIRA 32LEC05T2S LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 32LEC05T2S LED TV:

About Mainboard:

AKIRA 32LED02T2M LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 32LED02T2M LED TV:

About Mainboard:

AKIRA 32LED38T2P LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 32LED38T2P LED TV:

About Mainboard:

AKIRA 39LED01T2M LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 39LED01T2M LED TV:

About Mainboard:

AKIRA 32LED38P LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA 32LED38P LED TV:

About Mainboard:

AKIRA LCT-32V88MMP LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA LCT-32V88MMP LED TV:

About Mainboard:

AKIRA LCT-22V82ST LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA LCT-22V82ST LED TV:

About Mainboard:

AKIRA LCT-47CH19ST LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKIRA LCT-47CH19ST LED TV:

About Mainboard:

Adblock Detected