All Universal Board Firmware Free Download

  • N.M358.801 EMMC SOFTWARE DOWNLOAD

    N.M358.801 EMMC SOFTWARE

    N.M358.801 EMMC dump file is shared for repairing purpose. If the N.M358.801 does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then EMMC dump file can be loaded.

    Troubleshooting Guide:

    If the N.M358.801 is dead. Mean no power no indication light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    N.M358.801 EMMC

    If both are found ok and N.M358.801 is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load EMMC dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the N.M358.801 are tested and found accurate then write EMMC dump file because it seems to be a software problem. I hope the issue will be resolved by rewriting EMMC memory.

    Installation Instructions:

    For writing EMMC dump file in N.M358.801 board, first of all save the backup of old EMMC data then erase the EMMC chip to clear any bad sector. After it write the given N.M358.801 EMMC dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the EMMC dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications N.M358.801:

    • Make/Brand: Universal
    • Main Board/Chassis: N.M358.801
    • Power Source: AC220
    • Rated Power Consumption:
    • Panel Info: HD
    • T-CON:
    • Main Processor/Chipset: MSD358
    • EMMC: 4GB
    • Firmware Type: EMMC Backup
    • Product User: Universal
    • Product Model: Universal

    Click for more EMMC Dumps TV

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the EMMC Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in case of any damage/loss.

    FLASH DUMP FILES

    How to Download Free Software for N.M358.801:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • ACONATIC AN-LT4712 FIRMWARE FREE

    ACONATIC AN-LT4712 USB FIRMWARE

    ACONATIC AN-LT4712 LED TV software file is shared for repairing purpose. If the ACONATIC AN-LT4712 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then this software file can be loaded by USB. If the ACONATIC AN-LT4712 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse may burnt and cut off the supply.

    If both are found ok and ACONATIC AN-LT4712 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load software file the TV will be normal after repairing and if the standby light is indicating and the TV still not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the ACONATIC AN-LT4712 LED TV are tested and found accurate then load software file because this seems to be a software problem, hope the issue will be resolved by installing this USB Boot Software.

    ACONATIC AN-LT4712

    Installation Instructions:

    For installing USB Boot file in ACONATIC AN-LT4712 LED TV board, first of all save the backup if you have any programming device. This software file is compatible with ACONATIC AN-LT4712 LED TV. USB Disk must be formatted with FAT32 system. Mostly new FAT 32 devices are not supported for USB Boot so, make sure that USB disk is compatible. Transfer the given software file into USB disk and plug in into USB port of ACONATIC AN-LT4712 LED TV Mainboard and switch on. It will flash automatically. After Completion remove the USB disk and power on the TV. Hope TV will be normal now. If you have any problem by installing software then Read Here.

    Technical Specifications ACONATIC AN-LT4712 LED TV:

    • Make/Brand: Aconatic
    • Main Board/Chassis: *35017328
    • Board Type: Smart
    • Power Source: 100~240V
    • Rated Power Consumption: 95W
    • Panel Info: FHD
    • T-CON:
    • Screen Resolution: 1920×1080
    • Main Processor/Chipset:
    • SPI Flash: NA
    • Tuner:
    • Firmware Type: USB Upgrade
    • Product User: Aconatic
    • Product Model: AN-LT4712

    Click for more LED TV Software

    Special Note:

    The attached software is USB Boot file and can be loaded by a USB Disk in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before installing software. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in case of any damage/loss.

    About Mainboard

    ACONATIC AN-LT4712 LED TV firmware file is shared below for repairing the firmware problem. ACONATIC AN-LT4712 LED TV has the main board 35017328 installed in it so the given firmware file is compatible with board 35017328 by loading USB Boot. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 35017328 firmware file is shared below for the ACONATIC AN-LT4712 LED TV repairing.

    FLASH DUMP FILES

    How to Download Free Firmware for ACONATIC AN-LT4712 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • EUROSTAR T32LED-A14 EMMC DUMP

    EUROSTAR T32LED-A14 EMMC SOFTWARE

    EUROSTAR T32LED-A14 LED TV EMMC dump file is shared for repairing purpose. If the EUROSTAR T32LED-A14 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then EMMC dump file can be loaded.

    Troubleshooting Guide:

    If the EUROSTAR T32LED-A14 LED TV is dead. Mean no power no indication light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    EUROSTAR T32LED-A14

    If both are found ok and EUROSTAR T32LED-A14 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load EMMC dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the EUROSTAR T32LED-A14 LED TV are tested and found accurate then write EMMC dump file because it seems to be a software problem. I hope the issue will be resolved by rewriting EMMC memory.

    Installation Instructions:

    For writing EMMC dump file in EUROSTAR T32LED-A14 LED TV board, first of all save the backup of old EMMC data then erase the EMMC chip to clear any bad sector. After it write the given EUROSTAR T32LED-A14 LED TV EMMC dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the EMMC dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications EUROSTAR T32LED-A14 LED TV:

    • Make/Brand: EUROSTAR
    • Main Board/Chassis: TP.MS608.P83
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: LC320ESN-D00
    • T-CON:
    • Main Processor/Chipset: MSD6A608HTAB-Z1
    • EMMC: 4GB
    • Firmware Type: EMMC DUMP
    • Product User: EUROSTAR
    • Product Model: T32LED-A14

    Click for more EMMC Dumps TV

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the EMMC Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in case of any damage/loss.

    FLASH DUMP FILES

    How to Download Free Software for EUROSTAR T32LED-A14 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • BRANDT BAB32H5SN HD EMMC DUMP

    BRANDT BAB32H5SN HD EMMC SOFTWARE

    BRANDT BAB32H5SN LED TV EMMC dump file is shared for repairing purpose. If the BRANDT BAB32H5SN LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then EMMC dump file can be loaded.

    Troubleshooting Guide:

    If the BRANDT BAB32H5SN LED TV is dead. Mean no power no indication light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    BRANDT BAB32H5SN

    If both are found ok and BRANDT BAB32H5SN LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load EMMC dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRANDT BAB32H5SN LED TV are tested and found accurate then write EMMC dump file because it seems to be a software problem. I hope the issue will be resolved by rewriting EMMC memory.

    Installation Instructions:

    For writing EMMC dump file in BRANDT BAB32H5SN LED TV board, first of all save the backup of old EMMC data then erase the EMMC chip to clear any bad sector. After it write the given BRANDT BAB32H5SN LED TV EMMC dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the EMMC dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BRANDT BAB32H5SN LED TV:

    • Make/Brand: BRANDT
    • Main Board/Chassis: P75-628VX v6.0
    • Power Source: 100-240V
    • Rated Power Consumption: 55W
    • Panel Info: LC320DXE-SFR1 HD
    • T-CON:
    • Main Processor/Chipset: MAD6A628
    • EMMC: 4GB
    • Firmware Type: EMMC BACKUP
    • Product User: BRANDT
    • Product Model: BAB32H5SN

    Click for more EMMC Dumps TV

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the EMMC Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in case of any damage/loss.

    FLASH DUMP FILES

    How to Download Free Software for BRANDT BAB32H5SN LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • ATA 42S1 FHD EMMC DUMP

    ATA 42S1 FHD EMMC SOFTWARE

    ATA 42S1 LED TV EMMC dump file is shared for repairing purpose. If the ATA 42S1 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then EMMC dump file can be loaded.

    Troubleshooting Guide:

    If the ATA 42S1 LED TV is dead. Mean no power no indication light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the
    supply.

    ATA 42S1

    If both are found ok and ATA 42S1 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load EMMC dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the ATA 42S1 LED TV are tested and found accurate then write EMMC dump file because it seems to be a software problem. I hope the issue will be resolved by rewriting EMMC memory.

    Installation Instructions:

    For writing EMMC dump file in ATA 42S1 LED TV board, first of all save the backup of old EMMC data then erase the EMMC chip to clear any bad sector. After it write the given ATA 42S1 LED TV EMMC dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the EMMC dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications ATA 42S1 LED TV:

    • Make/Brand: ATA
    • Main Board/Chassis: TP.RT2982.PB801
    • Power Source: 100-240V
    • Rated Power Consumption: 85W
    • Panel Info: LC420DUJ FHD
    • T-CON:
    • Main Processor/Chipset: RTD2982DQ
    • EMMC: 4GB
    • Firmware Type: EMMC Backup
    • Product User: ATA
    • Product Model: 42S1
    • Firmware Name: allupgrade_2982_92.img
    • Firmware Info: CP86805_JP_TP_RT2982_PB801_EGYPT_LOGO_ATA_IR_RS36_LC420DUJ_SGE1_1920X1080_REF92

    Click for more EMMC Dumps TV

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position.
    Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the EMMC Dump File. If you are not a technician or do not have any
    experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in
    case of any damage/loss.

    FLASH DUMP FILES

    How to Download Free Software for ATA 42S1 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • SAMSUNG UA32H4500AW EMMC DUMP

    SAMSUNG UA32H4500AW EMMC SOFTWARE

    SAMSUNG UA32H4500AW LED TV EMMC dump file is shared for repairing purpose. If the SAMSUNG UA32H4500AW LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then EMMC dump file can be loaded.

    Troubleshooting Guide:

    If the SAMSUNG UA32H4500AW LED TV is dead. Mean no power no indication light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    SAMSUNG UA32H4500AW

    If both are found ok and SAMSUNG UA32H4500AW LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load EMMC dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SAMSUNG UA32H4500AW LED TV are tested and found accurate then write EMMC dump file because it seems to be a software problem. I hope the issue will be resolved by rewriting EMMC memory.

    Installation Instructions:

    For writing EMMC dump file in SAMSUNG UA32H4500AW LED TV board, first of all save the backup of old EMMC data then erase the EMMC chip to clear any bad sector. After it write the given SAMSUNG UA32H4500AW LED TV EMMC dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the EMMC dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SAMSUNG UA32H4500AW LED TV:

    • Make/Brand: SAMSUNG
    • Main Board/Chassis: BN41-02156A
    • Power Source: AC 100-240V
    • Rated Power Consumption: 68W
    • Panel Backlight Info: CY-HH032AGLV2H
    • T-CON:
    • Main Processor/Chipset: BN41
    • EMMC: KLM4G1FEAC-C031
    • Firmware Type: EMMC BACKUP
    • Product User: SAMSUNG
    • Product Model: UA32H4500AW

    Click for more EMMC Dumps TV

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the EMMC Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, as a result, board may be dead. Admin Team is not responsible in case of any damage/loss.

    FLASH DUMP FILES

    How to Download Free Software for SAMSUNG UA32H4500AW LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly