BBK Tv Software Update

  • BBK LM4027F LED TV FLASH DUMP

    BBK LM4027F LED TV

    BBK LM4027F LED TV Software file is shared for repairing purpose. If the BBK LM4027F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LM4027F

    Troubleshooting Guide:

    If the BBK LM4027F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LM4027F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LM4027F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LM4027F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LM4027F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LM4027F LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: T.MS18VG.21B 11513
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LM4027F LED TV dump file is shared below for repairing the firmware problem. BBK LM4027F LED TV has the main board T.MS18VG.21B 11513 installed in it so the SPI Flash file backup saved from working board T.MS18VG.21B 11513. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.21B 11513 dump file is shared below for the BBK LM4027F LED TV repairing.

    Download
    BBK LM4027F LED TV Software download free.

    How to Download Free Software for BBK LM4027F LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM4289F LED TV FLASH DUMP

    BBK LEM4289F LED TV

    BBK LEM4289F LED TV Software file is shared for repairing purpose. If the BBK LEM4289F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM4289F

    Troubleshooting Guide:

    If the BBK LEM4289F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM4289F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM4289F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM4289F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM4289F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM4289F LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: E182VG-Z0-A0
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM4289F LED TV dump file is shared below for repairing the firmware problem. BBK LEM4289F LED TV has the main board E182VG-Z0-A0 installed in it so the SPI Flash file backup saved from working board E182VG-Z0-A0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. E182VG-Z0-A0 dump file is shared below for the BBK LEM4289F LED TV repairing.

    Download
    BBK LEM4289F LED TV Software download free.

    How to Download Free Software for BBK LEM4289F LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM4079F LED TV FLASH DUMP

    BBK LEM4079F LED TV

    BBK LEM4079F LED TV Software file is shared for repairing purpose. If the BBK LEM4079F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM4079F

    Troubleshooting Guide:

    If the BBK LEM4079F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM4079F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM4079F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM4079F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM4079F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM4079F LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: E182VG-Z0-A0
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM4079F LED TV dump file is shared below for repairing the firmware problem. BBK LEM4079F LED TV has the main board E182VG-Z0-A0 installed in it so the SPI Flash file backup saved from working board E182VG-Z0-A0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. E182VG-Z0-A0 dump file is shared below for the BBK LEM4079F LED TV repairing.

    Download
    BBK LEM4079F LED TV Software download free.

    How to Download Free Software for BBK LEM4079F LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3289F LED TV FLASH DUMP

    BBK LEM3289F LED TV

    BBK LEM3289F LED TV Software file is shared for repairing purpose. If the BBK LEM3289F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3289F

    Troubleshooting Guide:

    If the BBK LEM3289F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3289F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3289F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3289F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3289F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3289F LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: E182VG-Z0-A0
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3289F LED TV dump file is shared below for repairing the firmware problem. BBK LEM3289F LED TV has the main board E182VG-Z0-A0 installed in it so the SPI Flash file backup saved from working board E182VG-Z0-A0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. E182VG-Z0-A0 dump file is shared below for the BBK LEM3289F LED TV repairing.

    Download
    BBK LEM3289F LED TV Software download free.

    How to Download Free Software for BBK LEM3289F LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3285FDTG LED TV FLASH DUMP

    BBK LEM3285FDTG LED TV

    BBK LEM3285FDTG LED TV Software file is shared for repairing purpose. If the BBK LEM3285FDTG LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3285FDTG

    Troubleshooting Guide:

    If the BBK LEM3285FDTG LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3285FDTG LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3285FDTG LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3285FDTG LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3285FDTG LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3285FDTG LED TV:

    • Make/Brand: BBK
    • Main Board/Chassis: MSDV3219-ZC01-01
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3285FDTG LED TV dump file is shared below for repairing the firmware problem. BBK LEM3285FDTG LED TV has the main board MSDV3219-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3219-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3219-ZC01-01 dump file is shared below for the BBK LEM3285FDTG LED TV repairing.

    Download
    BBK LEM3285FDTG LED TV Software download free.

    How to Download Free Software for BBK LEM3285FDTG LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3284DT2 LED TV FLASH DUMP

    BBK LEM3284DT2 LED TV

    BBK LEM3284DT2 LED TV Software file is shared for repairing purpose. If the BBK LEM3284DT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3284DT2

    Troubleshooting Guide:

    If the BBK LEM3284DT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3284DT2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3284DT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3284DT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3284DT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3284DT2 LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: MSDV3222-ZC01-01
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3284DT2 LED TV dump file is shared below for repairing the firmware problem. BBK LEM3284DT2 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the BBK LEM3284DT2 LED TV repairing.

    Download
    BBK LEM3284DT2 LED TV Software download free.

    How to Download Free Software for BBK LEM3284DT2 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3283F LED TV FLASH DUMP

    BBK LEM3283F LED TV

    BBK LEM3283F LED TV Software file is shared for repairing purpose. If the BBK LEM3283F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3283F

    Troubleshooting Guide:

    If the BBK LEM3283F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3283F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3283F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3283F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3283F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3283F LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: MS18VG.81B
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3283F LED TV dump file is shared below for repairing the firmware problem. BBK LEM3283F LED TV has the main board MS18VG.81B installed in it so the SPI Flash file backup saved from working board MS18VG.81B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MS18VG.81B dump file is shared below for the BBK LEM3283F LED TV repairing.

    Download
    BBK LEM3283F LED TV Software download free.

    How to Download Free Software for BBK LEM3283F LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3282DT LED TV FLASH DUMP

    BBK LEM3282DT LED TV

    BBK LEM3282DT LED TV Software file is shared for repairing purpose. If the BBK LEM3282DT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3282DT

    Troubleshooting Guide:

    If the BBK LEM3282DT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3282DT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3282DT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3282DT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3282DT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3282DT LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: MSDV3209-ZC01-01 (D)
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3282DT LED TV dump file is shared below for repairing the firmware problem. BBK LEM3282DT LED TV has the main board MSDV3209-ZC01-01 (D) installed in it so the SPI Flash file backup saved from working board MSDV3209-ZC01-01 (D). Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3209-ZC01-01 (D) dump file is shared below for the BBK LEM3282DT LED TV repairing.

    Download
    BBK LEM3282DT LED TV Software download free.

    How to Download Free Software for BBK LEM3282DT LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3281FDT LED TV FLASH DUMP

    BBK LEM3281FDT LED TV

    BBK LEM3281FDT LED TV Software file is shared for repairing purpose. If the BBK LEM3281FDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3281FDT

    Troubleshooting Guide:

    If the BBK LEM3281FDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3281FDT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3281FDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3281FDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3281FDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3281FDT LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: MSDV3209-ZC01-01 (D)
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3281FDT LED TV dump file is shared below for repairing the firmware problem. BBK LEM3281FDT LED TV has the main board MSDV3209-ZC01-01 (D) installed in it so the SPI Flash file backup saved from working board MSDV3209-ZC01-01 (D). Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3209-ZC01-01 (D) dump file is shared below for the BBK LEM3281FDT LED TV repairing.

    Download
    BBK LEM3281FDT LED TV Software download free.

    How to Download Free Software for BBK LEM3281FDT LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • BBK LEM3264F LED TV FLASH DUMP

    BBK LEM3264F LED TV

    BBK LEM3264F LED TV Software file is shared for repairing purpose. If the BBK LEM3264F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3264F

    Troubleshooting Guide:

    If the BBK LEM3264F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3264F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3264F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3264F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3264F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3264F LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: 868M.JUG7.820 1221
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3264F LED TV dump file is shared below for repairing the firmware problem. BBK LEM3264F LED TV has the main board 868M.JUG7.820 1221 installed in it so the SPI Flash file backup saved from working board 868M.JUG7.820 1221. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 868M.JUG7.820 1221 dump file is shared below for the BBK LEM3264F LED TV repairing.

    Download
    BBK LEM3264F LED TV Software download free.

    How to Download Free Software for BBK LEM3264F LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly