BBK Tv Software Update

18/03/2023
0 16

BBK LEM2683F LED TV FLASH DUMP
Download Here

BBK LEM2683F LED TV

BBK LEM2683F LED TV Software file is shared for repairing purpose. If the BBK LEM2683F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2683F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2683F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2683F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2683F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2683F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2683F LED TV:
- Make/Brand: BBK
- Main Board/Chassis: T.MS18VG.81B 11467
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2683F LED TV dump file is shared below for repairing the firmware problem. BBK LEM2683F LED TV has the main board T.MS18VG.81B 11467 installed in it so the SPI Flash file backup saved from working board T.MS18VG.81B 11467. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.81B 11467 dump file is shared below for the BBK LEM2683F LED TV repairing.

BBK LEM2683F LED TV Software download free.

How to Download Free Software for BBK LEM2683F LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 22

BBK LEM2682DT LED TV FLASH DUMP
Download Here

BBK LEM2682DT LED TV

BBK LEM2682DT LED TV Software file is shared for repairing purpose. If the BBK LEM2682DT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2682DT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2682DT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2682DT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2682DT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2682DT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2682DT LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3213-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2682DT LED TV dump file is shared below for repairing the firmware problem. BBK LEM2682DT LED TV has the main board MSDV3213-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3213-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3213-ZC01-01 dump file is shared below for the BBK LEM2682DT LED TV repairing.

BBK LEM2682DT LED TV Software download free.

How to Download Free Software for BBK LEM2682DT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 25

BBK LEM2681FDT LED TV FLASH DUMP
Download Here

BBK LEM2681FDT LED TV

BBK LEM2681FDT LED TV Software file is shared for repairing purpose. If the BBK LEM2681FDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2681FDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2681FDT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2681FDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2681FDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2681FDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2681FDT LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3213-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2681FDT LED TV dump file is shared below for repairing the firmware problem. BBK LEM2681FDT LED TV has the main board MSDV3213-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3213-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3213-ZC01-01 dump file is shared below for the BBK LEM2681FDT LED TV repairing.

BBK LEM2681FDT LED TV Software download free.

How to Download Free Software for BBK LEM2681FDT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 17

BBK LEM2665FDTG LED TV FLASH DUMP
Download Here

BBK LEM2665FDTG LED TV

BBK LEM2665FDTG LED TV Software file is shared for repairing purpose. If the BBK LEM2665FDTG LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2665FDTG LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2665FDTG LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2665FDTG LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2665FDTG LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2665FDTG LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2665FDTG LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3209-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2665FDTG LED TV dump file is shared below for repairing the firmware problem. BBK LEM2665FDTG LED TV has the main board MSDV3209-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3209-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3209-ZC01-01 dump file is shared below for the BBK LEM2665FDTG LED TV repairing.

BBK LEM2665FDTG LED TV Software download free.

How to Download Free Software for BBK LEM2665FDTG LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 162

BBK LEM2649FDT LED TV FLASH DUMP
Download Here

BBK LEM2649FDT LED TV

BBK LEM2649FDT LED TV Software file is shared for repairing purpose. If the BBK LEM2649FDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2649FDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2649FDT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2649FDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2649FDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2649FDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2649FDT LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3209-ZC01-01 (D)
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2649FDT LED TV dump file is shared below for repairing the firmware problem. BBK LEM2649FDT LED TV has the main board MSDV3209-ZC01-01 (D) installed in it so the SPI Flash file backup saved from working board MSDV3209-ZC01-01 (D). Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3209-ZC01-01 (D) dump file is shared below for the BBK LEM2649FDT LED TV repairing.

BBK LEM2649FDT LED TV Software download free.

How to Download Free Software for BBK LEM2649FDT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 15

BBK LEM-2496F LED TV FLASH DUMP
Download Here

BBK LEM-2496F LED TV

BBK LEM-2496F LED TV Software file is shared for repairing purpose. If the BBK LEM-2496F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM-2496F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM-2496F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM-2496F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM-2496F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM-2496F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM-2496F LED TV:
- Make/Brand: BBK
- Main Board/Chassis: E182VG-Y0-E0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM-2496F LED TV dump file is shared below for repairing the firmware problem. BBK LEM-2496F LED TV has the main board E182VG-Y0-E0 installed in it so the SPI Flash file backup saved from working board E182VG-Y0-E0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. E182VG-Y0-E0 dump file is shared below for the BBK LEM-2496F LED TV repairing.

BBK LEM-2496F LED TV Software download free.

How to Download Free Software for BBK LEM-2496F LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 360

BBK LEM2495F LED TV FLASH DUMP
Download Here

BBK LEM2495F LED TV

BBK LEM2495F LED TV Software file is shared for repairing purpose. If the BBK LEM2495F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2495F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2495F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2495F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2495F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2495F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2495F LED TV:
- Make/Brand: BBK
- Main Board/Chassis: EV59XUS-Y1-A0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2495F LED TV dump file is shared below for repairing the firmware problem. BBK LEM2495F LED TV has the main board EV59XUS-Y1-A0 installed in it so the SPI Flash file backup saved from working board EV59XUS-Y1-A0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. EV59XUS-Y1-A0 dump file is shared below for the BBK LEM2495F LED TV repairing.

BBK LEM2495F LED TV Software download free.

How to Download Free Software for BBK LEM2495F LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 15

BBK LEM2488FDT LED TV FLASH DUMP
Download Here

BBK LEM2488FDT LED TV

BBK LEM2488FDT LED TV Software file is shared for repairing purpose. If the BBK LEM2488FDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2488FDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2488FDT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2488FDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2488FDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2488FDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2488FDT LED TV:
- Make/Brand: BBK
- Main Board/Chassis: L0M05 (1) ; 88XR-TL05022488FDT
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2488FDT LED TV dump file is shared below for repairing the firmware problem. BBK LEM2488FDT LED TV has the main board L0M05 (1) ; 88XR-TL05022488FDT installed in it so the SPI Flash file backup saved from working board L0M05 (1) ; 88XR-TL05022488FDT. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. L0M05 (1) ; 88XR-TL05022488FDT dump file is shared below for the BBK LEM2488FDT LED TV repairing.

BBK LEM2488FDT LED TV Software download free.

How to Download Free Software for BBK LEM2488FDT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 16

BBK LEM2485FDTG LED TV FLASH DUMP
Download Here

BBK LEM2485FDTG LED TV

BBK LEM2485FDTG LED TV Software file is shared for repairing purpose. If the BBK LEM2485FDTG LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2485FDTG LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2485FDTG LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2485FDTG LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2485FDTG LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2485FDTG LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2485FDTG LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3213-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2485FDTG LED TV dump file is shared below for repairing the firmware problem. BBK LEM2485FDTG LED TV has the main board MSDV3213-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3213-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3213-ZC01-01 dump file is shared below for the BBK LEM2485FDTG LED TV repairing.

BBK LEM2485FDTG LED TV Software download free.

How to Download Free Software for BBK LEM2485FDTG LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 17

BBK LEM2484DT2 LED TV FLASH DUMP
Download Here

BBK LEM2484DT2 LED TV

BBK LEM2484DT2 LED TV Software file is shared for repairing purpose. If the BBK LEM2484DT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2484DT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2484DT2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2484DT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2484DT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2484DT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2484DT2 LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2484DT2 LED TV dump file is shared below for repairing the firmware problem. BBK LEM2484DT2 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the BBK LEM2484DT2 LED TV repairing.

BBK LEM2484DT2 LED TV Software download free.

How to Download Free Software for BBK LEM2484DT2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done