BRAVIS Firmware Download

23/03/2023
0 28

BRAVIS LED-32E6001T2 LED TV FLASH DUMP
Download Here

BRAVIS LED-32E6001T2 LED TV

BRAVIS LED-32E6001T2 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-32E6001T2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-32E6001T2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-32E6001T2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-32E6001T2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-32E6001T2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-32E6001T2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-32E6001T2 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: JUC7.820.00189149
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-32E6001T2 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-32E6001T2 LED TV has the main board JUC7.820.00189149 installed in it so the SPI Flash file backup saved from working board JUC7.820.00189149. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. JUC7.820.00189149 dump file is shared below for the BRAVIS LED-32E6001T2 LED TV repairing.

BRAVIS LED-32E6001T2 LED TV Software download free.

How to Download Free Software for BRAVIS LED-32E6001T2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 23

BRAVIS PDP-50890 LED TV FLASH DUMP
Download Here

BRAVIS PDP-50890 LED TV

BRAVIS PDP-50890 LED TV Software file is shared for repairing purpose. If the BRAVIS PDP-50890 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS PDP-50890 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS PDP-50890 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS PDP-50890 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS PDP-50890 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS PDP-50890 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS PDP-50890 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: JUG7.820.1091-2
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS PDP-50890 LED TV dump file is shared below for repairing the firmware problem. BRAVIS PDP-50890 LED TV has the main board JUG7.820.1091-2 installed in it so the SPI Flash file backup saved from working board JUG7.820.1091-2. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. JUG7.820.1091-2 dump file is shared below for the BRAVIS PDP-50890 LED TV repairing.

BRAVIS PDP-50890 LED TV Software download free.

How to Download Free Software for BRAVIS PDP-50890 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 69

BRAVIS LED-32G5000T2 LED TV FLASH DUMP
Download Here

BRAVIS LED-32G5000T2 LED TV

BRAVIS LED-32G5000T2 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-32G5000T2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-32G5000T2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-32G5000T2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-32G5000T2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-32G5000T2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-32G5000T2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-32G5000T2 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: JUC7.820.00243887
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-32G5000T2 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-32G5000T2 LED TV has the main board JUC7.820.00243887 installed in it so the SPI Flash file backup saved from working board JUC7.820.00243887. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. JUC7.820.00243887 dump file is shared below for the BRAVIS LED-32G5000T2 LED TV repairing.

BRAVIS LED-32G5000T2 LED TV Software download free.

How to Download Free Software for BRAVIS LED-32G5000T2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 37

BRAVIS LED-32E2000 LED TV FLASH DUMP
Download Here

BRAVIS LED-32E2000 LED TV

BRAVIS LED-32E2000 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-32E2000 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-32E2000 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-32E2000 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-32E2000 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-32E2000 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-32E2000 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-32E2000 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: TP.VST59S.PB703
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-32E2000 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-32E2000 LED TV has the main board TP.VST59S.PB703 installed in it so the SPI Flash file backup saved from working board TP.VST59S.PB703. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.PB703 dump file is shared below for the BRAVIS LED-32E2000 LED TV repairing.

BRAVIS LED-32E2000 LED TV Software download free.

How to Download Free Software for BRAVIS LED-32E2000 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 25

BRAVIS LED-49E3000 LED TV FLASH DUMP
Download Here

BRAVIS LED-49E3000 LED TV

BRAVIS LED-49E3000 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-49E3000 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-49E3000 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-49E3000 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-49E3000 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-49E3000 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-49E3000 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-49E3000 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: TP.V56.PC821
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-49E3000 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-49E3000 LED TV has the main board TP.V56.PC821 installed in it so the SPI Flash file backup saved from working board TP.V56.PC821. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.V56.PC821 dump file is shared below for the BRAVIS LED-49E3000 LED TV repairing.

BRAVIS LED-49E3000 LED TV Software download free.

How to Download Free Software for BRAVIS LED-49E3000 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 36

BRAVIS LED-DB3200BH LED TV FLASH DUMP
Download Here

BRAVIS LED-DB3200BH LED TV

BRAVIS LED-DB3200BH LED TV Software file is shared for repairing purpose. If the BRAVIS LED-DB3200BH LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-DB3200BH LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-DB3200BH LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-DB3200BH LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-DB3200BH LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-DB3200BH LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-DB3200BH LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: TP.VST59.P86
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-DB3200BH LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-DB3200BH LED TV has the main board TP.VST59.P86 installed in it so the SPI Flash file backup saved from working board TP.VST59.P86. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59.P86 dump file is shared below for the BRAVIS LED-DB3200BH LED TV repairing.

BRAVIS LED-DB3200BH LED TV Software download free.

How to Download Free Software for BRAVIS LED-DB3200BH LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 144

BRAVIS LED-1516 LED TV FLASH DUMP
Download Here

BRAVIS LED-1516 LED TV

BRAVIS LED-1516 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-1516 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-1516 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-1516 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-1516 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-1516 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-1516 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-1516 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: T.VST59.A81
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-1516 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-1516 LED TV has the main board T.VST59.A81 installed in it so the SPI Flash file backup saved from working board T.VST59.A81. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST59.A81 dump file is shared below for the BRAVIS LED-1516 LED TV repairing.

BRAVIS LED-1516 LED TV Software download free.

How to Download Free Software for BRAVIS LED-1516 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 19

BRAVIS LED-4219 LED TV FLASH DUMP
Download Here

BRAVIS LED-4219 LED TV

BRAVIS LED-4219 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-4219 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-4219 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-4219 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-4219 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-4219 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-4219 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-4219 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: TP.VST59S.PB813
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-4219 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-4219 LED TV has the main board TP.VST59S.PB813 installed in it so the SPI Flash file backup saved from working board TP.VST59S.PB813. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.PB813 dump file is shared below for the BRAVIS LED-4219 LED TV repairing.

BRAVIS LED-4219 LED TV Software download free.

How to Download Free Software for BRAVIS LED-4219 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 20

BRAVIS LED-4028 LED TV FLASH DUMP
Download Here

BRAVIS LED-4028 LED TV

BRAVIS LED-4028 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-4028 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-4028 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-4028 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-4028 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-4028 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-4028 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-4028 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: TP.VST59S.PB813
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-4028 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-4028 LED TV has the main board TP.VST59S.PB813 installed in it so the SPI Flash file backup saved from working board TP.VST59S.PB813. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.PB813 dump file is shared below for the BRAVIS LED-4028 LED TV repairing.

BRAVIS LED-4028 LED TV Software download free.

How to Download Free Software for BRAVIS LED-4028 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
23/03/2023
0 20

BRAVIS LED-3230 LED TV FLASH DUMP
Download Here

BRAVIS LED-3230 LED TV

BRAVIS LED-3230 LED TV Software file is shared for repairing purpose. If the BRAVIS LED-3230 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BRAVIS LED-3230 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BRAVIS LED-3230 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BRAVIS LED-3230 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BRAVIS LED-3230 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BRAVIS LED-3230 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BRAVIS LED-3230 LED TV:
- Make/Brand: BRAVIS
- Main Board/Chassis: TP.VST59S.PB817
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BRAVIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BRAVIS LED-3230 LED TV dump file is shared below for repairing the firmware problem. BRAVIS LED-3230 LED TV has the main board TP.VST59S.PB817 installed in it so the SPI Flash file backup saved from working board TP.VST59S.PB817. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.PB817 dump file is shared below for the BRAVIS LED-3230 LED TV repairing.

BRAVIS LED-3230 LED TV Software download free.

How to Download Free Software for BRAVIS LED-3230 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done