China LCD LED TV Software Free Download

03/05/2024
0 1

SANSUI LEDTVHY2261FH7-A LED TV DUMP
SANSUI LEDTVHY2261FH7-A LED TV

SANSUI LEDTVHY2261FH7-A LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVHY2261FH7-A LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVHY2261FH7-A LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVHY2261FH7-A LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVHY2261FH7-A LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVHY2261FH7-A LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVHY2261FH7-A LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVHY2261FH7-A LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVHY2261FH7-A LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVHY2261FH7-A LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVHY2261FH7-A LED TV repairing.

SANSUI LEDTVHY2261FH7-A LED TV Software download free.

How to Download Free Software for SANSUI LEDTVHY2261FH7-A LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
02/05/2024
0 1

SANSUI LEDTVSMJ28HH07FA LED TV DUMP
SANSUI LEDTVSMJ28HH07FA LED TV

SANSUI LEDTVSMJ28HH07FA LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSMJ28HH07FA LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSMJ28HH07FA LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSMJ28HH07FA LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSMJ28HH07FA LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSMJ28HH07FA LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSMJ28HH07FA LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSMJ28HH07FA LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSMJ28HH07FA LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSMJ28HH07FA LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSMJ28HH07FA LED TV repairing.

SANSUI LEDTVSMJ28HH07FA LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSMJ28HH07FA LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
01/05/2024
0 5

SANSUI LEDTVSKN20HH07FTP LED TV DUMP
SANSUI LEDTVSKN20HH07FTP LED TV

SANSUI LEDTVSKN20HH07FTP LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSKN20HH07FTP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSKN20HH07FTP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSKN20HH07FTP LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSKN20HH07FTP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSKN20HH07FTP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSKN20HH07FTP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSKN20HH07FTP LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSKN20HH07FTP LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSKN20HH07FTP LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSKN20HH07FTP LED TV repairing.

SANSUI LEDTVSKN20HH07FTP LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSKN20HH07FTP LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
30/04/2024
0 3

SANSUI LEDTVSJX32HB02CAF LED TV DUMP
SANSUI LEDTVSJX32HB02CAF LED TV

SANSUI LEDTVSJX32HB02CAF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX32HB02CAF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX32HB02CAF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX32HB02CAF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX32HB02CAF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX32HB02CAF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX32HB02CAF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX32HB02CAF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX32HB02CAF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX32HB02CAF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX32HB02CAF LED TV repairing.

SANSUI LEDTVSJX32HB02CAF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX32HB02CAF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
29/04/2024
0 5

SANSUI LEDTVSJX32FB-2CAF LED TV DUMP
SANSUI LEDTVSJX32FB-2CAF LED TV

SANSUI LEDTVSJX32FB-2CAF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX32FB-2CAF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX32FB-2CAF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX32FB-2CAF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX32FB-2CAF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX32FB-2CAF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX32FB-2CAF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX32FB-2CAF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX32FB-2CAF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX32FB-2CAF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX32FB-2CAF LED TV repairing.

SANSUI LEDTVSJX32FB-2CAF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX32FB-2CAF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
28/04/2024
0 11

SANSUI LEDTVSJX24FB-2CTF LED TV DUMP
SANSUI LEDTVSJX24FB-2CTF LED TV

SANSUI LEDTVSJX24FB-2CTF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX24FB-2CTF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX24FB-2CTF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX24FB-2CTF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX24FB-2CTF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX24FB-2CTF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX24FB-2CTF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX24FB-2CTF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX24FB-2CTF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX24FB-2CTF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX24FB-2CTF LED TV repairing.

SANSUI LEDTVSJX24FB-2CTF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX24FB-2CTF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
27/04/2024
0 9

SANSUI LEDTVSJX24FB-2CKF LED TV DUMP
SANSUI LEDTVSJX24FB-2CKF LED TV

SANSUI LEDTVSJX24FB-2CKF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX24FB-2CKF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX24FB-2CKF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX24FB-2CKF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX24FB-2CKF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX24FB-2CKF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX24FB-2CKF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX24FB-2CKF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX24FB-2CKF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX24FB-2CKF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX24FB-2CKF LED TV repairing.

SANSUI LEDTVSJX24FB-2CKF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX24FB-2CKF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
26/04/2024
0 5

SANSUI LEDTVSJX24FB-2CHF LED TV DUMP
SANSUI LEDTVSJX24FB-2CHF LED TV

SANSUI LEDTVSJX24FB-2CHF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX24FB-2CHF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX24FB-2CHF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX24FB-2CHF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX24FB-2CHF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX24FB-2CHF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX24FB-2CHF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX24FB-2CHF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX24FB-2CHF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX24FB-2CHF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX24FB-2CHF LED TV repairing.

SANSUI LEDTVSJX24FB-2CHF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX24FB-2CHF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/04/2024
0 14

SANSUI LEDTVSJX24FB-2CAF LED TV DUMP
SANSUI LEDTVSJX24FB-2CAF LED TV

SANSUI LEDTVSJX24FB-2CAF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX24FB-2CAF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX24FB-2CAF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX24FB-2CAF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX24FB-2CAF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX24FB-2CAF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX24FB-2CAF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX24FB-2CAF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX24FB-2CAF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX24FB-2CAF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX24FB-2CAF LED TV repairing.

SANSUI LEDTVSJX24FB-2CAF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX24FB-2CAF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
24/04/2024
0 7

SANSUI LEDTVSJX24FB02CTF LED TV DUMP
SANSUI LEDTVSJX24FB02CTF LED TV

SANSUI LEDTVSJX24FB02CTF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX24FB02CTF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SANSUI LEDTVSJX24FB02CTF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SANSUI LEDTVSJX24FB02CTF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX24FB02CTF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SANSUI LEDTVSJX24FB02CTF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX24FB02CTF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SANSUI LEDTVSJX24FB02CTF LED TV:
- Make/Brand: SANSUI
- Main Board/Chassis: MTK8227-C
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SANSUI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SANSUI LEDTVSJX24FB02CTF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX24FB02CTF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX24FB02CTF LED TV repairing.

SANSUI LEDTVSJX24FB02CTF LED TV Software download free.

How to Download Free Software for SANSUI LEDTVSJX24FB02CTF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

SANSUI LEDTVHY2261FH7-A LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVHY2261FH7-A LED TV:

About Mainboard:

SANSUI LEDTVSMJ28HH07FA LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSMJ28HH07FA LED TV:

About Mainboard:

SANSUI LEDTVSKN20HH07FTP LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSKN20HH07FTP LED TV:

About Mainboard:

SANSUI LEDTVSJX32HB02CAF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX32HB02CAF LED TV:

About Mainboard:

SANSUI LEDTVSJX32FB-2CAF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX32FB-2CAF LED TV:

About Mainboard:

SANSUI LEDTVSJX24FB-2CTF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX24FB-2CTF LED TV:

About Mainboard:

SANSUI LEDTVSJX24FB-2CKF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX24FB-2CKF LED TV:

About Mainboard:

SANSUI LEDTVSJX24FB-2CHF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX24FB-2CHF LED TV:

About Mainboard:

SANSUI LEDTVSJX24FB-2CAF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX24FB-2CAF LED TV:

About Mainboard:

SANSUI LEDTVSJX24FB02CTF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SANSUI LEDTVSJX24FB02CTF LED TV:

About Mainboard:

Adblock Detected