CV3663BH-Q32

26/10/2023
0 22

PRESTIGIO PTV32SN05Z LED TV FLASH DUMP
Download Here

PRESTIGIO PTV32SN05Z LED TV

PRESTIGIO PTV32SN05Z LED TV Software file is shared for repairing purpose. If the PRESTIGIO PTV32SN05Z LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the PRESTIGIO PTV32SN05Z LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and PRESTIGIO PTV32SN05Z LED TV is still dead then check the primary power circuit if found ok then test the sPRESTIGIOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPRESTIGIOdary voltage of the main board of the PRESTIGIO PTV32SN05Z LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in PRESTIGIO PTV32SN05Z LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given PRESTIGIO PTV32SN05Z LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications PRESTIGIO PTV32SN05Z LED TV:
- Make/Brand: PRESTIGIO
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: PRESTIGIO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

PRESTIGIO PTV32SN05Z LED TV dump file is shared below for repairing the firmware problem. PRESTIGIO PTV32SN05Z LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the PRESTIGIO PTV32SN05Z LED TV repairing.

PRESTIGIO PTV32SN05Z LED TV Software download free.

How to Download Free Software for PRESTIGIO PTV32SN05Z LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/10/2023
0 16

PRESTIGIO PTV32SN04Z LED TV FLASH DUMP
Download Here

PRESTIGIO PTV32SN04Z LED TV

PRESTIGIO PTV32SN04Z LED TV Software file is shared for repairing purpose. If the PRESTIGIO PTV32SN04Z LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the PRESTIGIO PTV32SN04Z LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and PRESTIGIO PTV32SN04Z LED TV is still dead then check the primary power circuit if found ok then test the sPRESTIGIOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPRESTIGIOdary voltage of the main board of the PRESTIGIO PTV32SN04Z LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in PRESTIGIO PTV32SN04Z LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given PRESTIGIO PTV32SN04Z LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications PRESTIGIO PTV32SN04Z LED TV:
- Make/Brand: PRESTIGIO
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: PRESTIGIO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

PRESTIGIO PTV32SN04Z LED TV dump file is shared below for repairing the firmware problem. PRESTIGIO PTV32SN04Z LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the PRESTIGIO PTV32SN04Z LED TV repairing.

PRESTIGIO PTV32SN04Z LED TV Software download free.

How to Download Free Software for PRESTIGIO PTV32SN04Z LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
26/07/2023
0 16

IRBIS 32S80HD405B LED TV FLASH DUMP
Download Here

IRBIS 32S80HD405B LED TV

IRBIS 32S80HD405B LED TV Software file is shared for repairing purpose. If the IRBIS 32S80HD405B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IRBIS 32S80HD405B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IRBIS 32S80HD405B LED TV is still dead then check the primary power circuit if found ok then test the sIRBISdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIRBISdary voltage of the main board of the IRBIS 32S80HD405B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IRBIS 32S80HD405B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IRBIS 32S80HD405B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IRBIS 32S80HD405B LED TV:
- Make/Brand: IRBIS
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IRBIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IRBIS 32S80HD405B LED TV dump file is shared below for repairing the firmware problem. IRBIS 32S80HD405B LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the IRBIS 32S80HD405B LED TV repairing.

IRBIS 32S80HD405B LED TV Software download free.

How to Download Free Software for IRBIS 32S80HD405B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
06/07/2023
0 19

DEXP H32D7100E LED TV FLASH DUMP
Download Here

DEXP H32D7100E LED TV

DEXP H32D7100E LED TV Software file is shared for repairing purpose. If the DEXP H32D7100E LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DEXP H32D7100E LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DEXP H32D7100E LED TV is still dead then check the primary power circuit if found ok then test the sDEXPdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDEXPdary voltage of the main board of the DEXP H32D7100E LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DEXP H32D7100E LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DEXP H32D7100E LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DEXP H32D7100E LED TV:
- Make/Brand: DEXP
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DEXP
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DEXP H32D7100E LED TV dump file is shared below for repairing the firmware problem. DEXP H32D7100E LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the DEXP H32D7100E LED TV repairing.

DEXP H32D7100E LED TV Software download free.

How to Download Free Software for DEXP H32D7100E LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
14/03/2023
0 75

BBK 32LEM-1071TS2C LED TV FLASH DUMP
Download Here

BBK 32LEM-1071TS2C LED TV

BBK 32LEM-1071TS2C LED TV Software file is shared for repairing purpose. If the BBK 32LEM-1071TS2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK 32LEM-1071TS2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK 32LEM-1071TS2C LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK 32LEM-1071TS2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK 32LEM-1071TS2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK 32LEM-1071TS2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK 32LEM-1071TS2C LED TV:
- Make/Brand: BBK
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK 32LEM-1071TS2C LED TV dump file is shared below for repairing the firmware problem. BBK 32LEM-1071TS2C LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the BBK 32LEM-1071TS2C LED TV repairing.

BBK 32LEM-1071TS2C LED TV Software download free.

How to Download Free Software for BBK 32LEM-1071TS2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
14/03/2023
0 84

BBK 32LEM-1066TS2C LED TV FLASH DUMP
Download Here

BBK 32LEM-1066TS2C LED TV

BBK 32LEM-1066TS2C LED TV Software file is shared for repairing purpose. If the BBK 32LEM-1066TS2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK 32LEM-1066TS2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK 32LEM-1066TS2C LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK 32LEM-1066TS2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK 32LEM-1066TS2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK 32LEM-1066TS2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK 32LEM-1066TS2C LED TV:
- Make/Brand: BBK
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: CX315DLEM
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK 32LEM-1066TS2C LED TV dump file is shared below for repairing the firmware problem. BBK 32LEM-1066TS2C LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the BBK 32LEM-1066TS2C LED TV repairing.

BBK 32LEM-1066TS2C LED TV Software download free.

How to Download Free Software for BBK 32LEM-1066TS2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
14/03/2023
0 14

BBK 32LEM-1047TS2C LED TV FLASH DUMP
Download Here

BBK 32LEM-1047TS2C LED TV

BBK 32LEM-1047TS2C LED TV Software file is shared for repairing purpose. If the BBK 32LEM-1047TS2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK 32LEM-1047TS2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK 32LEM-1047TS2C LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK 32LEM-1047TS2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK 32LEM-1047TS2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK 32LEM-1047TS2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK 32LEM-1047TS2C LED TV:
- Make/Brand: BBK
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: CX315DLEM
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK 32LEM-1047TS2C LED TV dump file is shared below for repairing the firmware problem. BBK 32LEM-1047TS2C LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the BBK 32LEM-1047TS2C LED TV repairing.

BBK 32LEM-1047TS2C LED TV Software download free.

How to Download Free Software for BBK 32LEM-1047TS2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/02/2023
0 15

AMCV LE32-ZTH15 LED TV FLASH DUMP
Download Here

AMCV LE32-ZTH15 LED TV

AMCV LE32-ZTH15 LED TV Software file is shared for repairing purpose. If the AMCV LE32-ZTH15 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AMCV LE32-ZTH15 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AMCV LE32-ZTH15 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AMCV LE32-ZTH15 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AMCV LE32-ZTH15 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AMCV LE32-ZTH15 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AMCV LE32-ZTH15 LED TV:
- Make/Brand: AMCV
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: CX315DLEM
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AMCV
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AMCV LE32-ZTH15 LED TV dump file is shared below for repairing the firmware problem. AMCV LE32-ZTH15 LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the AMCV LE32-ZTH15 LED TV repairing.

AMCV LE32-ZTH15 LED TV Software download free.

How to Download Free Software for AMCV LE32-ZTH15 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
11/02/2023
0 14

SUPRA STV-LC32LT0095W LED TV FLASH DUMP
Download Here

SUPRA STV-LC32LT0095W LED TV

SUPRA STV-LC32LT0095W LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC32LT0095W LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC32LT0095W LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC32LT0095W LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC32LT0095W LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC32LT0095W LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC32LT0095W LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC32LT0095W LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: CV3663BH-Q32
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: ST3151A05-8
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC32LT0095W LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC32LT0095W LED TV has the main board CV3663BH-Q32 installed in it so the SPI Flash file backup saved from working board CV3663BH-Q32. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV3663BH-Q32 dump file is shared below for the SUPRA STV-LC32LT0095W LED TV repairing.

SUPRA STV-LC32LT0095W LED TV Software download free.

How to Download Free Software for SUPRA STV-LC32LT0095W LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

PRESTIGIO PTV32SN05Z LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications PRESTIGIO PTV32SN05Z LED TV:

About Mainboard:

PRESTIGIO PTV32SN04Z LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications PRESTIGIO PTV32SN04Z LED TV:

About Mainboard:

IRBIS 32S80HD405B LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications IRBIS 32S80HD405B LED TV:

About Mainboard:

DEXP H32D7100E LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DEXP H32D7100E LED TV:

About Mainboard:

BBK 32LEM-1071TS2C LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications BBK 32LEM-1071TS2C LED TV:

About Mainboard:

BBK 32LEM-1066TS2C LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications BBK 32LEM-1066TS2C LED TV:

About Mainboard:

BBK 32LEM-1047TS2C LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications BBK 32LEM-1047TS2C LED TV:

About Mainboard:

AMCV LE32-ZTH15 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AMCV LE32-ZTH15 LED TV:

About Mainboard:

SUPRA STV-LC32LT0095W LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SUPRA STV-LC32LT0095W LED TV:

About Mainboard:

Adblock Detected