DVR

  • 15/11/2021
    0 933

    HIKVISION DS 7208HQHI K1E FLASH DUMP

    HIKVISION DS 7208HQHI K1E

    HIKVISION DS 7208HQHI K1E DVR flash dump file is shared for repairing purpose. If the HIKVISION DS 7208HQHI K1E DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the HIKVISION DS 7208HQHI K1E DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and HIKVISION DS 7208HQHI K1E DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the HIKVISION DS 7208HQHI K1E DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in HIKVISION DS 7208HQHI K1E DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given HIKVISION DS 7208HQHI K1E DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications HIKVISION DS 7208HQHI K1E DVR:

    • Make/Brand: HIKVISION
    • DVR Model: DS-7208HQHI-K1E
    • Main Board/Chassis:
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: W25Q128
    • Channel Capacity: 8 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached HIKVISION DS 7208HQHI K1E software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    1 1,468

    HIKVISION DS 7208HGHI F1 FLASH DUMP

    HIKVISION DS 7208HGHI F1

    HIKVISION DS 7208HGHI F1 DVR flash dump file is shared for repairing purpose. If the HIKVISION DS 7208HGHI F1 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the HIKVISION DS 7208HGHI F1 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and HIKVISION DS 7208HGHI F1 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the HIKVISION DS 7208HGHI F1 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in HIKVISION DS 7208HGHI F1 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given HIKVISION DS 7208HGHI F1 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications HIKVISION DS 7208HGHI F1 DVR:

    • Make/Brand: HIKVISION
    • DVR Model: DS-7208HGHI-F1
    • Main Board/Chassis:
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: 25Q128
    • Channel Capacity: 8 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached HIKVISION DS 7208HGHI F1 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 871

    HIKVISION DS 7204HQHI DS 80160 DUMP

    HIKVISION DS 7204HQHI DS 80160

    HIKVISION DS 7204HQHI DS 80160 DVR flash dump file is shared for repairing purpose. If the HIKVISION DS 7204HQHI DS 80160 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the HIKVISION DS 7204HQHI DS 80160 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and HIKVISION DS 7204HQHI DS 80160 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the HIKVISION DS 7204HQHI DS 80160 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in HIKVISION DS 7204HQHI DS 80160 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given HIKVISION DS 7204HQHI DS 80160 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications HIKVISION DS 7204HQHI DS 80160 DVR:

    • Make/Brand: HIKVISION
    • DVR Model: DS 7204HQHI
    • Main Board/Chassis: DS 80160
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash:
    • Channel Capacity:
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached HIKVISION DS 7204HQHI DS 80160 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 116

    DVR KNG 5104 Hi3250 FLASH DUMP

    DVR KNG 5104 Hi3250

    DVR KNG 5104 Hi3250 DVR flash dump file is shared for repairing purpose. If the DVR KNG 5104 Hi3250 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR KNG 5104 Hi3250 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR KNG 5104 Hi3250 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR KNG 5104 Hi3250 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in DVR KNG 5104 Hi3250 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR KNG 5104 Hi3250 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR KNG 5104 Hi3250 DVR:

    • Make/Brand: KING
    • DVR Model: KNG 5104
    • Main Board/Chassis: 3250DV300-2824-4CH
    • Power Source: DC 12V
    • Main Processor/Chipset: HI3520
    • SPI Flash: 25L128
    • Channel Capacity: 4 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR KNG 5104 Hi3250 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 131

    DVR 8808 T3515AS V1.06 FLASH DUMP

    DVR 8808 T3515AS V1.06

    DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR flash dump file is shared for repairing purpose. If the DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 DVR:

    • Make/Brand: DVR
    • DVR Model: 8808
    • Main Board/Chassis: T3515AS V1.06-AT T3520DH 8S 4
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash:
    • Channel Capacity:
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR 8808 T3515AS V1.06-AT T3520DH 8S 4 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 359

    DVR ZOOM HVR5004HF VER 1.2 FLASH DUMP

    DVR ZOOM HVR5004HF VER 1.2

    DVR ZOOM HDVR5004HF VER 1.2 DVR flash dump file is shared for repairing purpose. If the DVR ZOOM HDVR5004HF VER 1.2 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR ZOOM HDVR5004HF VER 1.2 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR ZOOM HDVR5004HF VER 1.2 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR ZOOM HDVR5004HF VER 1.2 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in DVR ZOOM HDVR5004HF VER 1.2 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR ZOOM HDVR5004HF VER 1.2 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR ZOOM HDVR5004HF VER 1.2 DVR:

    • Make/Brand: ZOOM
    • DVR Model:
    • Main Board/Chassis: HDVR5004HF VER 1.2
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: 25Q128
    • Channel Capacity: 4 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR ZOOM HDVR5004HF VER 1.2 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 102

    DVR YEAMA7 FLASH DUMP

    DVR YEAMA7

    DVR YEAMA7 DVR flash dump file is shared for repairing purpose. If the DVR YEAMA7 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR YEAMA7 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR YEAMA7 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR YEAMA7 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in DVR YEAMA7 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR YEAMA7 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR YEAMA7 DVR:

    • Make/Brand: YEAMA7
    • DVR Model: HD 4CH KIT
    • Main Board/Chassis: RS-AT2304N-C3
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: 25Q128
    • Channel Capacity: 4 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR YEAMA7 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 917

    DVR XPOD XP7104-4H1 DS-80237 FLASH DUMP

    DVR XPOD XP7104-4H1 DS-80237

    DVR XPOD XP7104-4H1 DS-80237 DVR flash dump file is shared for repairing purpose. If the DVR XPOD XP7104-4H1 DS-80237 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR XPOD XP7104-4H1 DS-80237 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR XPOD XP7104-4H1 DS-80237 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR XPOD XP7104-4H1 DS-80237 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

     

    For writing flash dump file in DVR XPOD XP7104-4H1 DS-80237 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR XPOD XP7104-4H1 DS-80237 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR XPOD XP7104-4H1 DS-80237 DVR:

    • Make/Brand: XPOD
    • DVR Model: XP7104-4H1
    • Main Board/Chassis: DS-80237_P REV6.0
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: 25Q128
    • Channel Capacity: 4 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR XPOD XP7104-4H1 DS-80237 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 23

    DVR XPOD 8286 8AHD V1 FLASH DUMP

    DVR XPOD 8286 8AHD V1

    DVR XPOD 8286 8AHD V1 DVR flash dump file is shared for repairing purpose. If the DVR XPOD 8286 8AHD V1 DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR XPOD 8286 8AHD V1 DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR XPOD 8286 8AHD V1 DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR XPOD 8286 8AHD V1 DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in DVR XPOD 8286 8AHD V1 DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR XPOD 8286 8AHD V1 DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR XPOD 8286 8AHD V1 DVR:

    • Make/Brand: DVR XPOD
    • DVR Model:
    • Main Board/Chassis: 8286 8AHD V1
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: 25Q128
    • Channel Capacity: 8 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR XPOD 8286 8AHD V1 software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

  • 15/11/2021
    0 31

    DVR U VISION UV-3316P FLASH DUMP

    DVR U VISION UV-3316P

    DVR U VISION UV-3316P DVR flash dump file is shared for repairing purpose. If the DVR U VISION UV-3316P DVR does not turn on mean not leaving the standby position or no display and even the control buttons/keys on DVR not working then flash dump file can be loaded. If the DVR U VISION UV-3316P DVR is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit on the mainboard. In start check the main input if available then also check the power cable/wire continuity. If both are found ok and DVR U VISION UV-3316P DVR is still dead then visually check the mainboard and if found ok then test/measure the core voltage. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the DVR will be normal after repairing and if the standby light is indicating and the DVR not leaving standby or no any display and also all the core voltage of the main board of the DVR U VISION UV-3316P DVR are measured and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in DVR U VISION UV-3316P DVR board, first of all save the backup of old dump then erase the flash chip. After it write the given DVR U VISION UV-3316P DVR flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the channel capacity is different. In these cases you can write the flash dump file it may work but extra channels will be displayed on screen.

    Technical Specifications DVR U VISION UV-3316P DVR:

    • Make/Brand: U VISION
    • DVR Model: UV-3316P
    • Main Board/Chassis:
    • Power Source: DC 12V
    • Main Processor/Chipset:
    • SPI Flash: 25Q128
    • Channel Capacity: 16 CH
    • Firmware Type: SPI Dump

    DVR Info:

    Special Note:

    The attached DVR U VISION UV-3316P software is backup dump file and can be loaded by a programming tool in case when DVR stuck on Logo or Boot Screen or not leaving the standby position or display screen malfunctioning. Not for Update purpose if DVR is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps

Next page
error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly