led tv software free download

  • SANSUI LCDTVSAL26HMA-FLB LED TV DUMP

    SANSUI LCDTVSAL26HMA-FLB LED TV

    SANSUI LCDTVSAL26HMA-FLB LED TV Software file is shared for repairing purpose. If the SANSUI LCDTVSAL26HMA-FLB LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LCDTVSAL26HMA-FLB

    Troubleshooting Guide:

    If the SANSUI LCDTVSAL26HMA-FLB LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LCDTVSAL26HMA-FLB LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LCDTVSAL26HMA-FLB LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LCDTVSAL26HMA-FLB LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LCDTVSAL26HMA-FLB LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LCDTVSAL26HMA-FLB LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MST719_20.05.2010_22
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LCDTVSAL26HMA-FLB LED TV dump file is shared below for repairing the firmware problem. SANSUI LCDTVSAL26HMA-FLB LED TV has the main board MST719_20.05.2010_22 installed in it so the SPI Flash file backup saved from working board MST719_20.05.2010_22. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST719_20.05.2010_22 dump file is shared below for the SANSUI LCDTVSAL26HMA-FLB LED TV repairing.

    Download

    SANSUI LCDTVSAL26HMA-FLB LED TV Software download free.

    How to Download Free Software for SANSUI LCDTVSAL26HMA-FLB LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LCDTVSAL26HMA-FLA LED TV DUMP

    SANSUI LCDTVSAL26HMA-FLA LED TV

    SANSUI LCDTVSAL26HMA-FLA LED TV Software file is shared for repairing purpose. If the SANSUI LCDTVSAL26HMA-FLA LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LCDTVSAL26HMA-FLA

    Troubleshooting Guide:

    If the SANSUI LCDTVSAL26HMA-FLA LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LCDTVSAL26HMA-FLA LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LCDTVSAL26HMA-FLA LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LCDTVSAL26HMA-FLA LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LCDTVSAL26HMA-FLA LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LCDTVSAL26HMA-FLA LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: AX68_SAN
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LCDTVSAL26HMA-FLA LED TV dump file is shared below for repairing the firmware problem. SANSUI LCDTVSAL26HMA-FLA LED TV has the main board AX68_SAN installed in it so the SPI Flash file backup saved from working board AX68_SAN. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. AX68_SAN dump file is shared below for the SANSUI LCDTVSAL26HMA-FLA LED TV repairing.

    Download

    SANSUI LCDTVSAL26HMA-FLA LED TV Software download free.

    How to Download Free Software for SANSUI LCDTVSAL26HMA-FLA LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSKN20HH07FAP LED TV DUMP

    SANSUI LEDTVSKN20HH07FAP LED TV

    SANSUI LEDTVSKN20HH07FAP LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSKN20HH07FAP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSKN20HH07FAP

    Troubleshooting Guide:

    If the SANSUI LEDTVSKN20HH07FAP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSKN20HH07FAP LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSKN20HH07FAP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSKN20HH07FAP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSKN20HH07FAP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSKN20HH07FAP LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSKN20HH07FAP LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSKN20HH07FAP LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSKN20HH07FAP LED TV repairing.

    Download

    SANSUI LEDTVSKN20HH07FAP LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSKN20HH07FAP LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSKJ20HH07FAP LED TV DUMP

    SANSUI LEDTVSKJ20HH07FAP LED TV

    SANSUI LEDTVSKJ20HH07FAP LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSKJ20HH07FAP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSKJ20HH07FAP

    Troubleshooting Guide:

    If the SANSUI LEDTVSKJ20HH07FAP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSKJ20HH07FAP LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSKJ20HH07FAP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSKJ20HH07FAP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSKJ20HH07FAP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSKJ20HH07FAP LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSKJ20HH07FAP LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSKJ20HH07FAP LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSKJ20HH07FAP LED TV repairing.

    Download

    SANSUI LEDTVSKJ20HH07FAP LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSKJ20HH07FAP LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSJX32HB07CKF LED TV DUMP

    SANSUI LEDTVSJX32HB07CKF LED TV

    SANSUI LEDTVSJX32HB07CKF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX32HB07CKF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSJX32HB07CKF

    Troubleshooting Guide:

    If the SANSUI LEDTVSJX32HB07CKF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSJX32HB07CKF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX32HB07CKF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSJX32HB07CKF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX32HB07CKF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSJX32HB07CKF LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSJX32HB07CKF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX32HB07CKF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX32HB07CKF LED TV repairing.

    Download

    SANSUI LEDTVSJX32HB07CKF LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSJX32HB07CKF LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSJX32HB07CAF LED TV DUMP

    SANSUI LEDTVSJX32HB07CAF LED TV

    SANSUI LEDTVSJX32HB07CAF LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSJX32HB07CAF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSJX32HB07CAF

    Troubleshooting Guide:

    If the SANSUI LEDTVSJX32HB07CAF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSJX32HB07CAF LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSJX32HB07CAF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSJX32HB07CAF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSJX32HB07CAF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSJX32HB07CAF LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSJX32HB07CAF LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSJX32HB07CAF LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSJX32HB07CAF LED TV repairing.

    Download

    SANSUI LEDTVSJX32HB07CAF LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSJX32HB07CAF LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LCDTVSAL26HBA-FLU LED TV DUMP

    SANSUI LCDTVSAL26HBA-FLU LED TV

    SANSUI LCDTVSAL26HBA-FLU LED TV Software file is shared for repairing purpose. If the SANSUI LCDTVSAL26HBA-FLU LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LCDTVSAL26HBA-FLU

    Troubleshooting Guide:

    If the SANSUI LCDTVSAL26HBA-FLU LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LCDTVSAL26HBA-FLU LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LCDTVSAL26HBA-FLU LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LCDTVSAL26HBA-FLU LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LCDTVSAL26HBA-FLU LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LCDTVSAL26HBA-FLU LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MST719_20.05.2010_22
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LCDTVSAL26HBA-FLU LED TV dump file is shared below for repairing the firmware problem. SANSUI LCDTVSAL26HBA-FLU LED TV has the main board MST719_20.05.2010_22 installed in it so the SPI Flash file backup saved from working board MST719_20.05.2010_22. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST719_20.05.2010_22 dump file is shared below for the SANSUI LCDTVSAL26HBA-FLU LED TV repairing.

    Download

    SANSUI LCDTVSAL26HBA-FLU LED TV Software download free.

    How to Download Free Software for SANSUI LCDTVSAL26HBA-FLU LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSKN20HH07FA LED TV DUMP

    SANSUI LEDTVSKN20HH07FA LED TV

    SANSUI LEDTVSKN20HH07FA LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSKN20HH07FA LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSKN20HH07FA

    Troubleshooting Guide:

    If the SANSUI LEDTVSKN20HH07FA LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSKN20HH07FA LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSKN20HH07FA LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSKN20HH07FA LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSKN20HH07FA LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSKN20HH07FA LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSKN20HH07FA LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSKN20HH07FA LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSKN20HH07FA LED TV repairing.

    Download

    SANSUI LEDTVSKN20HH07FA LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSKN20HH07FA LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSKN20HH07FT LED TV DUMP

    SANSUI LEDTVSKN20HH07FT LED TV

    SANSUI LEDTVSKN20HH07FT LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSKN20HH07FT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSKN20HH07FT

    Troubleshooting Guide:

    If the SANSUI LEDTVSKN20HH07FT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSKN20HH07FT LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSKN20HH07FT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSKN20HH07FT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSKN20HH07FT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSKN20HH07FT LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSKN20HH07FT LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSKN20HH07FT LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSKN20HH07FT LED TV repairing.

    Download

    SANSUI LEDTVSKN20HH07FT LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSKN20HH07FT LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • SANSUI LEDTVSKJ20HH07FKP LED TV DUMP

    SANSUI LEDTVSKJ20HH07FKP LED TV

    SANSUI LEDTVSKJ20HH07FKP LED TV Software file is shared for repairing purpose. If the SANSUI LEDTVSKJ20HH07FKP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SANSUI LEDTVSKJ20HH07FKP

    Troubleshooting Guide:

    If the SANSUI LEDTVSKJ20HH07FKP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SANSUI LEDTVSKJ20HH07FKP LED TV is still dead then check the primary power circuit if found ok then test the sSANSUIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSANSUIdary voltage of the main board of the SANSUI LEDTVSKJ20HH07FKP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SANSUI LEDTVSKJ20HH07FKP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SANSUI LEDTVSKJ20HH07FKP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SANSUI LEDTVSKJ20HH07FKP LED TV:
    • Make/Brand: SANSUI
    • Main Board/Chassis: MTK8227-C
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SANSUI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SANSUI LEDTVSKJ20HH07FKP LED TV dump file is shared below for repairing the firmware problem. SANSUI LEDTVSKJ20HH07FKP LED TV has the main board MTK8227-C installed in it so the SPI Flash file backup saved from working board MTK8227-C. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MTK8227-C dump file is shared below for the SANSUI LEDTVSKJ20HH07FKP LED TV repairing.

    Download

    SANSUI LEDTVSKJ20HH07FKP LED TV Software download free.

    How to Download Free Software for SANSUI LEDTVSKJ20HH07FKP LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly