MANTA Viera Custom Firmware

  • MANTA LED280Q4 LED TV FLASH DUMP

    MANTA LED280Q4 LED TV

    MANTA LED280Q4 LED TV Software file is shared for repairing purpose. If the MANTA LED280Q4 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED280Q4

    Troubleshooting Guide:

    If the MANTA LED280Q4 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED280Q4 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED280Q4 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED280Q4 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED280Q4 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED280Q4 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK.T.RT2957P68
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED280Q4 LED TV dump file is shared below for repairing the firmware problem. MANTA LED280Q4 LED TV has the main board HK.T.RT2957P68 installed in it so the SPI Flash file backup saved from working board HK.T.RT2957P68. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.RT2957P68 dump file is shared below for the MANTA LED280Q4 LED TV repairing.

    Download

    MANTA LED280Q4 LED TV Software download free.

    How to Download Free Software for MANTA LED280Q4 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED1903V3 LED TV FLASH DUMP

    MANTA LED1903V3 LED TV

    MANTA LED1903V3 LED TV Software file is shared for repairing purpose. If the MANTA LED1903V3 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED1903V3

    Troubleshooting Guide:

    If the MANTA LED1903V3 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED1903V3 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED1903V3 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED1903V3 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED1903V3 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED1903V3 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK-T.RT2957E01
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED1903V3 LED TV dump file is shared below for repairing the firmware problem. MANTA LED1903V3 LED TV has the main board HK-T.RT2957E01 installed in it so the SPI Flash file backup saved from working board HK-T.RT2957E01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.RT2957E01 dump file is shared below for the MANTA LED1903V3 LED TV repairing.

    Download

    MANTA LED1903V3 LED TV Software download free.

    How to Download Free Software for MANTA LED1903V3 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA 50LFN59C LED TV FLASH DUMP

    MANTA 50LFN59C LED TV

    MANTA 50LFN59C LED TV Software file is shared for repairing purpose. If the MANTA 50LFN59C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA 50LFN59C

    Troubleshooting Guide:

    If the MANTA 50LFN59C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA 50LFN59C LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA 50LFN59C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA 50LFN59C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA 50LFN59C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA 50LFN59C LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK.T.RT2957P91
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA 50LFN59C LED TV dump file is shared below for repairing the firmware problem. MANTA 50LFN59C LED TV has the main board HK.T.RT2957P91 installed in it so the SPI Flash file backup saved from working board HK.T.RT2957P91. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.RT2957P91 dump file is shared below for the MANTA 50LFN59C LED TV repairing.

    Download

    MANTA 50LFN59C LED TV Software download free.

    How to Download Free Software for MANTA 50LFN59C LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA 32LFN58C LED TV FLASH DUMP

    MANTA 32LFN58C LED TV

    MANTA 32LFN58C LED TV Software file is shared for repairing purpose. If the MANTA 32LFN58C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA 32LFN58C

    Troubleshooting Guide:

    If the MANTA 32LFN58C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA 32LFN58C LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA 32LFN58C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA 32LFN58C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA 32LFN58C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA 32LFN58C LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK.T.RT2957P68
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA 32LFN58C LED TV dump file is shared below for repairing the firmware problem. MANTA 32LFN58C LED TV has the main board HK.T.RT2957P68 installed in it so the SPI Flash file backup saved from working board HK.T.RT2957P68. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.RT2957P68 dump file is shared below for the MANTA 32LFN58C LED TV repairing.

    Download

    MANTA 32LFN58C LED TV Software download free.

    How to Download Free Software for MANTA 32LFN58C LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED3903 LED TV FLASH DUMP

    MANTA LED3903 LED TV

    MANTA LED3903 LED TV Software file is shared for repairing purpose. If the MANTA LED3903 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED3903

    Troubleshooting Guide:

    If the MANTA LED3903 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED3903 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED3903 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED3903 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED3903 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED3903 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK-T.RT2957P61
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED3903 LED TV dump file is shared below for repairing the firmware problem. MANTA LED3903 LED TV has the main board HK-T.RT2957P61 installed in it so the SPI Flash file backup saved from working board HK-T.RT2957P61. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.RT2957P61 dump file is shared below for the MANTA LED3903 LED TV repairing.

    Download

    MANTA LED3903 LED TV Software download free.

    How to Download Free Software for MANTA LED3903 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED3204 LED TV FLASH DUMP

    MANTA LED3204 LED TV

    MANTA LED3204 LED TV Software file is shared for repairing purpose. If the MANTA LED3204 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED3204

    Troubleshooting Guide:

    If the MANTA LED3204 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED3204 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED3204 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED3204 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED3204 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED3204 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK-T.RT2957P62
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED3204 LED TV dump file is shared below for repairing the firmware problem. MANTA LED3204 LED TV has the main board HK-T.RT2957P62 installed in it so the SPI Flash file backup saved from working board HK-T.RT2957P62. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.RT2957P62 dump file is shared below for the MANTA LED3204 LED TV repairing.

    Download

    MANTA LED3204 LED TV Software download free.

    How to Download Free Software for MANTA LED3204 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED2803 LED TV FLASH DUMP

    MANTA LED2803 LED TV

    MANTA LED2803 LED TV Software file is shared for repairing purpose. If the MANTA LED2803 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED2803

    Troubleshooting Guide:

    If the MANTA LED2803 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED2803 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED2803 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED2803 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED2803 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED2803 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK-T.RT2957P61
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED2803 LED TV dump file is shared below for repairing the firmware problem. MANTA LED2803 LED TV has the main board HK-T.RT2957P61 installed in it so the SPI Flash file backup saved from working board HK-T.RT2957P61. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.RT2957P61 dump file is shared below for the MANTA LED2803 LED TV repairing.

    Download

    MANTA LED2803 LED TV Software download free.

    How to Download Free Software for MANTA LED2803 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED93206 LED TV FLASH DUMP

    MANTA LED93206 LED TV

    MANTA LED93206 LED TV Software file is shared for repairing purpose. If the MANTA LED93206 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED93206

    Troubleshooting Guide:

    If the MANTA LED93206 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED93206 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED93206 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED93206 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED93206 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED93206 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK-T.RT2957P62
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED93206 LED TV dump file is shared below for repairing the firmware problem. MANTA LED93206 LED TV has the main board HK-T.RT2957P62 installed in it so the SPI Flash file backup saved from working board HK-T.RT2957P62. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.RT2957P62 dump file is shared below for the MANTA LED93206 LED TV repairing.

    Download

    MANTA LED93206 LED TV Software download free.

    How to Download Free Software for MANTA LED93206 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED5003V LED TV FLASH DUMP

    MANTA LED5003V LED TV

    MANTA LED5003V LED TV Software file is shared for repairing purpose. If the MANTA LED5003V LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED5003V

    Troubleshooting Guide:

    If the MANTA LED5003V LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED5003V LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED5003V LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED5003V LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED5003V LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED5003V LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK.T.RT2957P91
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED5003V LED TV dump file is shared below for repairing the firmware problem. MANTA LED5003V LED TV has the main board HK.T.RT2957P91 installed in it so the SPI Flash file backup saved from working board HK.T.RT2957P91. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK.T.RT2957P91 dump file is shared below for the MANTA LED5003V LED TV repairing.

    Download

    MANTA LED5003V LED TV Software download free.

    How to Download Free Software for MANTA LED5003V LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • MANTA LED2403 LED TV FLASH DUMP

    MANTA LED2403 LED TV

    MANTA LED2403 LED TV Software file is shared for repairing purpose. If the MANTA LED2403 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    MANTA LED2403

    Troubleshooting Guide:

    If the MANTA LED2403 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and MANTA LED2403 LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA LED2403 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in MANTA LED2403 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA LED2403 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications MANTA LED2403 LED TV:
    • Make/Brand: MANTA
    • Main Board/Chassis: HK-T.RT2957E01
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: MANTA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    MANTA LED2403 LED TV dump file is shared below for repairing the firmware problem. MANTA LED2403 LED TV has the main board HK-T.RT2957E01 installed in it so the SPI Flash file backup saved from working board HK-T.RT2957E01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.RT2957E01 dump file is shared below for the MANTA LED2403 LED TV repairing.

    Download

    MANTA LED2403 LED TV Software download free.

    How to Download Free Software for MANTA LED2403 LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly