MSDV3222-ZC01-01

20/08/2023
0 10

JVC LT-32M345 LED TV FLASH DUMP
JVC LT-32M345 LED TV

JVC LT-32M345 LED TV Software file is shared for repairing purpose. If the JVC LT-32M345 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the JVC LT-32M345 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and JVC LT-32M345 LED TV is still dead then check the primary power circuit if found ok then test the sJVCdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sJVCdary voltage of the main board of the JVC LT-32M345 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in JVC LT-32M345 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given JVC LT-32M345 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications JVC LT-32M345 LED TV:
- Make/Brand: JVC
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: JVC
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

JVC LT-32M345 LED TV dump file is shared below for repairing the firmware problem. JVC LT-32M345 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the JVC LT-32M345 LED TV repairing.

JVC LT-32M345 LED TV Software download free.

How to Download Free Software for JVC LT-32M345 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/08/2023
0 13

JVC LT-24M440 LED TV FLASH DUMP
JVC LT-24M440 LED TV

JVC LT-24M440 LED TV Software file is shared for repairing purpose. If the JVC LT-24M440 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the JVC LT-24M440 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and JVC LT-24M440 LED TV is still dead then check the primary power circuit if found ok then test the sJVCdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sJVCdary voltage of the main board of the JVC LT-24M440 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in JVC LT-24M440 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given JVC LT-24M440 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications JVC LT-24M440 LED TV:
- Make/Brand: JVC
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: JVC
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

JVC LT-24M440 LED TV dump file is shared below for repairing the firmware problem. JVC LT-24M440 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the JVC LT-24M440 LED TV repairing.

JVC LT-24M440 LED TV Software download free.

How to Download Free Software for JVC LT-24M440 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
17/08/2023
0 21

JVC LT-24M440W LED TV FLASH DUMP
JVC LT-24M440W LED TV

JVC LT-24M440W LED TV Software file is shared for repairing purpose. If the JVC LT-24M440W LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the JVC LT-24M440W LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and JVC LT-24M440W LED TV is still dead then check the primary power circuit if found ok then test the sJVCdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sJVCdary voltage of the main board of the JVC LT-24M440W LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in JVC LT-24M440W LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given JVC LT-24M440W LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications JVC LT-24M440W LED TV:
- Make/Brand: JVC
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: JVC
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

JVC LT-24M440W LED TV dump file is shared below for repairing the firmware problem. JVC LT-24M440W LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the JVC LT-24M440W LED TV repairing.

JVC LT-24M440W LED TV Software download free.

How to Download Free Software for JVC LT-24M440W LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
17/08/2023
0 8

JVC LT-32M340W LED TV FLASH DUMP
JVC LT-32M340W LED TV

JVC LT-32M340W LED TV Software file is shared for repairing purpose. If the JVC LT-32M340W LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the JVC LT-32M340W LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and JVC LT-32M340W LED TV is still dead then check the primary power circuit if found ok then test the sJVCdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sJVCdary voltage of the main board of the JVC LT-32M340W LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in JVC LT-32M340W LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given JVC LT-32M340W LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications JVC LT-32M340W LED TV:
- Make/Brand: JVC
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: JVC
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

JVC LT-32M340W LED TV dump file is shared below for repairing the firmware problem. JVC LT-32M340W LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the JVC LT-32M340W LED TV repairing.

JVC LT-32M340W LED TV Software download free.

How to Download Free Software for JVC LT-32M340W LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
17/08/2023
0 16

JVC LT-22M445 LED TV FLASH DUMP
JVC LT-22M445 LED TV

JVC LT-22M445 LED TV Software file is shared for repairing purpose. If the JVC LT-22M445 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the JVC LT-22M445 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and JVC LT-22M445 LED TV is still dead then check the primary power circuit if found ok then test the sJVCdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sJVCdary voltage of the main board of the JVC LT-22M445 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in JVC LT-22M445 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given JVC LT-22M445 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications JVC LT-22M445 LED TV:
- Make/Brand: JVC
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: JVC
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

JVC LT-22M445 LED TV dump file is shared below for repairing the firmware problem. JVC LT-22M445 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the JVC LT-22M445 LED TV repairing.

JVC LT-22M445 LED TV Software download free.

How to Download Free Software for JVC LT-22M445 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
16/08/2023
0 66

JVC LT-28M340 LED TV FLASH DUMP
JVC LT-28M340 LED TV

JVC LT-28M340 LED TV Software file is shared for repairing purpose. If the JVC LT-28M340 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the JVC LT-28M340 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and JVC LT-28M340 LED TV is still dead then check the primary power circuit if found ok then test the sJVCdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sJVCdary voltage of the main board of the JVC LT-28M340 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in JVC LT-28M340 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given JVC LT-28M340 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications JVC LT-28M340 LED TV:
- Make/Brand: JVC
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: JVC
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

JVC LT-28M340 LED TV dump file is shared below for repairing the firmware problem. JVC LT-28M340 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the JVC LT-28M340 LED TV repairing.

JVC LT-28M340 LED TV Software download free.

How to Download Free Software for JVC LT-28M340 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 12

BBK LEM3284DT2 LED TV FLASH DUMP
BBK LEM3284DT2 LED TV

BBK LEM3284DT2 LED TV Software file is shared for repairing purpose. If the BBK LEM3284DT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM3284DT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM3284DT2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3284DT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM3284DT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3284DT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM3284DT2 LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM3284DT2 LED TV dump file is shared below for repairing the firmware problem. BBK LEM3284DT2 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the BBK LEM3284DT2 LED TV repairing.

BBK LEM3284DT2 LED TV Software download free.

How to Download Free Software for BBK LEM3284DT2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 15

BBK LEM2484DT2 LED TV FLASH DUMP
BBK LEM2484DT2 LED TV

BBK LEM2484DT2 LED TV Software file is shared for repairing purpose. If the BBK LEM2484DT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2484DT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2484DT2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2484DT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2484DT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2484DT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2484DT2 LED TV:
- Make/Brand: BBK
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2484DT2 LED TV dump file is shared below for repairing the firmware problem. BBK LEM2484DT2 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the BBK LEM2484DT2 LED TV repairing.

BBK LEM2484DT2 LED TV Software download free.

How to Download Free Software for BBK LEM2484DT2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
20/12/2022
0 3,045

MYSTERY MTV-3228LT2 LED TV FLASH DUMP
MYSTERY MTV-3228LT2 LED TV

MYSTERY MTV-3228LT2 LED TV Software file is shared for repairing purpose. If the MYSTERY MTV-3228LT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the MYSTERY MTV-3228LT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and MYSTERY MTV-3228LT2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the MYSTERY MTV-3228LT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in MYSTERY MTV-3228LT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MYSTERY MTV-3228LT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications MYSTERY MTV-3228LT2 LED TV:
- Make/Brand: MYSTERY
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LK315T3HB94
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash: 25Q64BS1G
- Tuner:
- Firmware Type: SPI Dump
- Product User: MYSTERY
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

MYSTERY MTV-3228LT2 LED TV dump file is shared below for repairing the firmware problem. MYSTERY MTV-3228LT2 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the MYSTERY MTV-3228LT2 LED TV repairing.

MYSTERY MTV-3228LT2 LED TV Software download free.

How to Download Free Software for MYSTERY MTV-3228LT2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
20/12/2022
0 20

MYSTERY MTV-1929LT2 LED TV FLASH DUMP
MYSTERY MTV-1929LT2 LED TV

MYSTERY MTV-1929LT2 LED TV Software file is shared for repairing purpose. If the MYSTERY MTV-1929LT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the MYSTERY MTV-1929LT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and MYSTERY MTV-1929LT2 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the MYSTERY MTV-1929LT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in MYSTERY MTV-1929LT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MYSTERY MTV-1929LT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications MYSTERY MTV-1929LT2 LED TV:
- Make/Brand: MYSTERY
- Main Board/Chassis: MSDV3222-ZC01-01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: V185BJ1-PE1
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash: GD25Q64BV
- Tuner:
- Firmware Type: SPI Dump
- Product User: MYSTERY
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

MYSTERY MTV-1929LT2 LED TV dump file is shared below for repairing the firmware problem. MYSTERY MTV-1929LT2 LED TV has the main board MSDV3222-ZC01-01 installed in it so the SPI Flash file backup saved from working board MSDV3222-ZC01-01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MSDV3222-ZC01-01 dump file is shared below for the MYSTERY MTV-1929LT2 LED TV repairing.

MYSTERY MTV-1929LT2 LED TV Software download free.

How to Download Free Software for MYSTERY MTV-1929LT2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

JVC LT-32M345 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications JVC LT-32M345 LED TV:

About Mainboard:

JVC LT-24M440 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications JVC LT-24M440 LED TV:

About Mainboard:

JVC LT-24M440W LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications JVC LT-24M440W LED TV:

About Mainboard:

JVC LT-32M340W LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications JVC LT-32M340W LED TV:

About Mainboard:

JVC LT-22M445 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications JVC LT-22M445 LED TV:

About Mainboard:

JVC LT-28M340 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications JVC LT-28M340 LED TV:

About Mainboard:

BBK LEM3284DT2 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications BBK LEM3284DT2 LED TV:

About Mainboard:

BBK LEM2484DT2 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications BBK LEM2484DT2 LED TV:

About Mainboard:

MYSTERY MTV-3228LT2 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications MYSTERY MTV-3228LT2 LED TV:

About Mainboard:

MYSTERY MTV-1929LT2 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications MYSTERY MTV-1929LT2 LED TV:

About Mainboard:

Adblock Detected