Sony Firmware Download

  • 07/06/2022
    0 24

    VIDEOCON LEDTVVJW32HH-5FA USB SOFTWARE

    VIDEOCON LEDTVVJW32HH-5FA LED TV SOFTWARE

    VIDEOCON LEDTVVJW32HH-5FA LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJW32HH-5FA LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJW32HH-5FA

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJW32HH-5FA LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJW32HH-5FA LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJW32HH-5FA LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJW32HH-5FA LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJW32HH-5FA LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJW32HH-5FA LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJW32HH-5FA
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJW32HH-5FA LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJW32HH-5FA LED TV has the main board LEDTVVJW32HH-5FA installed in it so the SPI Flash file backup saved from working board LEDTVVJW32HH-5FA. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJW32HH-5FA dump file is shared below for the VIDEOCON LEDTVVJW32HH-5FA LED TV repairing.

    VIDEOCON LEDTVVJW32HH-5FA

    How to Download Free Software for VIDEOCON LEDTVVJW32HH-5FA LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 14

    VIDEOCON LEDTVVRU32HHZFZ USB SOFTWARE

    VIDEOCON LEDTVVRU32HHZFZ LED TV SOFTWARE

    VIDEOCON LEDTVVRU32HHZFZ LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVRU32HHZFZ LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVRU32HHZFZ

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVRU32HHZFZ LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVRU32HHZFZ LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVRU32HHZFZ LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVRU32HHZFZ LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVRU32HHZFZ LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVRU32HHZFZ LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVRU32HHZFZ
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVRU32HHZFZ LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVRU32HHZFZ LED TV has the main board LEDTVVRU32HHZFZ installed in it so the SPI Flash file backup saved from working board LEDTVVRU32HHZFZ. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVRU32HHZFZ dump file is shared below for the VIDEOCON LEDTVVRU32HHZFZ LED TV repairing.

    VIDEOCON LEDTVVRU32HHZFZ

    How to Download Free Software for VIDEOCON LEDTVVRU32HHZFZ LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 89

    VIDEOCON LEDTVVJG24HH-ZMK USB SOFTWARE

    VIDEOCON LEDTVVJG24HH-ZMK LED TV SOFTWARE

    VIDEOCON LEDTVVJG24HH-ZMK LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJG24HH-ZMK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJG24HH-ZMK

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJG24HH-ZMK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJG24HH-ZMK LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJG24HH-ZMK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJG24HH-ZMK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJG24HH-ZMK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJG24HH-ZMK LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJG24HH-ZMK
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJG24HH-ZMK LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJG24HH-ZMK LED TV has the main board LEDTVVJG24HH-ZMK installed in it so the SPI Flash file backup saved from working board LEDTVVJG24HH-ZMK. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJG24HH-ZMK dump file is shared below for the VIDEOCON LEDTVVJG24HH-ZMK LED TV repairing.

    VIDEOCON LEDTVVJG24HH-ZMK

    How to Download Free Software for VIDEOCON LEDTVVJG24HH-ZMK LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 95

    VIDEOCON LEDTVVJG24HH-ZMA USB SOFTWARE

    VIDEOCON LEDTVVJG24HH-ZMA LED TV SOFTWARE

    VIDEOCON LEDTVVJG24HH-ZMA LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJG24HH-ZMA LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJG24HH-ZMA

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJG24HH-ZMA LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJG24HH-ZMA LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJG24HH-ZMA LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJG24HH-ZMA LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJG24HH-ZMA LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJG24HH-ZMA LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJG24HH-ZMA
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJG24HH-ZMA LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJG24HH-ZMA LED TV has the main board LEDTVVJG24HH-ZMA installed in it so the SPI Flash file backup saved from working board LEDTVVJG24HH-ZMA. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJG24HH-ZMA dump file is shared below for the VIDEOCON LEDTVVJG24HH-ZMA LED TV repairing.

    VIDEOCON LEDTVVJG24HH-ZMA

    How to Download Free Software for VIDEOCON LEDTVVJG24HH-ZMA LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 11

    VIDEOCON LEDTVVJW32HH-NFAE USB SOFTWARE

    VIDEOCON LEDTVVJW32HH-NFAE LED TV SOFTWARE

    VIDEOCON LEDTVVJW32HH-NFAE LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJW32HH-NFAE LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJW32HH-NFAE

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJW32HH-NFAE LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJW32HH-NFAE LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJW32HH-NFAE LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJW32HH-NFAE LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJW32HH-NFAE LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJW32HH-NFAE LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJW32HH-NFAE
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJW32HH-NFAE LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJW32HH-NFAE LED TV has the main board LEDTVVJW32HH-NFAE installed in it so the SPI Flash file backup saved from working board LEDTVVJW32HH-NFAE. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJW32HH-NFAE dump file is shared below for the VIDEOCON LEDTVVJW32HH-NFAE LED TV repairing.

    VIDEOCON LEDTVVJW32HH-NFAE

    How to Download Free Software for VIDEOCON LEDTVVJW32HH-NFAE LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 18

    VIDEOCON LEDTVVJW32HH-NFK USB SOFTWARE

    VIDEOCON LEDTVVJW32HH-NFK LED TV SOFTWARE

    VIDEOCON LEDTVVJW32HH-NFK LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJW32HH-NFK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJW32HH-NFK

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJW32HH-NFK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJW32HH-NFK LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJW32HH-NFK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJW32HH-NFK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJW32HH-NFK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJW32HH-NFK LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJW32HH-NFK
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJW32HH-NFK LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJW32HH-NFK LED TV has the main board LEDTVVJW32HH-NFK installed in it so the SPI Flash file backup saved from working board LEDTVVJW32HH-NFK. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJW32HH-NFK dump file is shared below for the VIDEOCON LEDTVVJW32HH-NFK LED TV repairing.

    VIDEOCON LEDTVVJW32HH-NFK

    How to Download Free Software for VIDEOCON LEDTVVJW32HH-NFK LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 15

    VIDEOCON LEDTVVJW32HH-NFB USB SOFTWARE

    VIDEOCON LEDTVVJW32HH-NFB LED TV SOFTWARE

    VIDEOCON LEDTVVJW32HH-NFB LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJW32HH-NFB LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJW32HH-NFB

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJW32HH-NFB LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJW32HH-NFB LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJW32HH-NFB LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJW32HH-NFB LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJW32HH-NFB LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJW32HH-NFB LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJW32HH-NFB
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJW32HH-NFB LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJW32HH-NFB LED TV has the main board LEDTVVJW32HH-NFB installed in it so the SPI Flash file backup saved from working board LEDTVVJW32HH-NFB. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJW32HH-NFB dump file is shared below for the VIDEOCON LEDTVVJW32HH-NFB LED TV repairing.

    VIDEOCON LEDTVVJW32HH-NFB

    How to Download Free Software for VIDEOCON LEDTVVJW32HH-NFB LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 16

    VIDEOCON LEDTVVJW32HH-N0K USB SOFTWARE

    VIDEOCON LEDTVVJW32HH-N0K LED TV SOFTWARE

    VIDEOCON LEDTVVJW32HH-N0K LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJW32HH-N0K LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJW32HH-N0K

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJW32HH-N0K LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJW32HH-N0K LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJW32HH-N0K LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJW32HH-N0K LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJW32HH-N0K LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJW32HH-N0K LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJW32HH-N0K
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJW32HH-N0K LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJW32HH-N0K LED TV has the main board LEDTVVJW32HH-N0K installed in it so the SPI Flash file backup saved from working board LEDTVVJW32HH-N0K. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJW32HH-N0K dump file is shared below for the VIDEOCON LEDTVVJW32HH-N0K LED TV repairing.

    VIDEOCON LEDTVVJW32HH-N0K

    How to Download Free Software for VIDEOCON LEDTVVJW32HH-N0K LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 31

    VIDEOCON LEDTVVJW32HH-N0A USB SOFTWARE

    VIDEOCON LEDTVVJW32HH-N0A LED TV SOFTWARE

    VIDEOCON LEDTVVJW32HH-N0A LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJW32HH-N0A LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJW32HH-N0A

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJW32HH-N0A LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJW32HH-N0A LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJW32HH-N0A LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJW32HH-N0A LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJW32HH-N0A LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJW32HH-N0A LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJW32HH-N0A
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJW32HH-N0A LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJW32HH-N0A LED TV has the main board LEDTVVJW32HH-N0A installed in it so the SPI Flash file backup saved from working board LEDTVVJW32HH-N0A. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJW32HH-N0A dump file is shared below for the VIDEOCON LEDTVVJW32HH-N0A LED TV repairing.

    VIDEOCON LEDTVVJW32HH-N0A

    How to Download Free Software for VIDEOCON LEDTVVJW32HH-N0A LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

  • 07/06/2022
    0 35

    VIDEOCON LEDTVVJQ19HH-NMT USB SOFTWARE

    VIDEOCON LEDTVVJQ19HH-NMT LED TV SOFTWARE

    VIDEOCON LEDTVVJQ19HH-NMT LED TV Software file is shared for repairing purpose. If the VIDEOCON LEDTVVJQ19HH-NMT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VIDEOCON LEDTVVJQ19HH-NMT

    Troubleshooting Guide:

    If the VIDEOCON LEDTVVJQ19HH-NMT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VIDEOCON LEDTVVJQ19HH-NMT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the VIDEOCON LEDTVVJQ19HH-NMT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VIDEOCON LEDTVVJQ19HH-NMT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VIDEOCON LEDTVVJQ19HH-NMT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VIDEOCON LEDTVVJQ19HH-NMT LED TV:
    • Make/Brand: VIDEOCON
    • Main Board/Chassis: LEDTVVJQ19HH-NMT
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VIDEOCON
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VIDEOCON LEDTVVJQ19HH-NMT LED TV dump file is shared below for repairing the firmware problem. VIDEOCON LEDTVVJQ19HH-NMT LED TV has the main board LEDTVVJQ19HH-NMT installed in it so the SPI Flash file backup saved from working board LEDTVVJQ19HH-NMT. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. LEDTVVJQ19HH-NMT dump file is shared below for the VIDEOCON LEDTVVJQ19HH-NMT LED TV repairing.

    VIDEOCON LEDTVVJQ19HH-NMT

    How to Download Free Software for VIDEOCON LEDTVVJQ19HH-NMT LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done

Next page
error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly