SUPRA Viera Custom Firmware

12/02/2023
0 83

SUPRA STV-LC40T420FL LED TV FLASH DUMP
Download Here

SUPRA STV-LC40T420FL LED TV

SUPRA STV-LC40T420FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC40T420FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC40T420FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC40T420FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC40T420FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC40T420FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC40T420FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC40T420FL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: 40-T31T0T-MAD2HG
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LVF400CMOT E7 V4
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC40T420FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC40T420FL LED TV has the main board 40-T31T0T-MAD2HG installed in it so the SPI Flash file backup saved from working board 40-T31T0T-MAD2HG. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 40-T31T0T-MAD2HG dump file is shared below for the SUPRA STV-LC40T420FL LED TV repairing.

SUPRA STV-LC40T420FL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC40T420FL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 567

SUPRA STV-LC28T850WL LED TV FLASH DUMP
Download Here

SUPRA STV-LC28T850WL LED TV

SUPRA STV-LC28T850WL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC28T850WL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC28T850WL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC28T850WL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC28T850WL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC28T850WL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC28T850WL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC28T850WL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: MT31LB
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LVW280CSOT E8 V1
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC28T850WL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC28T850WL LED TV has the main board MT31LB installed in it so the SPI Flash file backup saved from working board MT31LB. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MT31LB dump file is shared below for the SUPRA STV-LC28T850WL LED TV repairing.

SUPRA STV-LC28T850WL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC28T850WL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 14

SUPRA STV-LC40T850FL LED TV FLASH DUMP
Download Here

SUPRA STV-LC40T850FL LED TV

SUPRA STV-LC40T850FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC40T850FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC40T850FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC40T850FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC40T850FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC40T850FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC40T850FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC40T850FL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: 40-T31TOT-MAB2HG
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LVF390CMOT
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC40T850FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC40T850FL LED TV has the main board 40-T31TOT-MAB2HG installed in it so the SPI Flash file backup saved from working board 40-T31TOT-MAB2HG. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 40-T31TOT-MAB2HG dump file is shared below for the SUPRA STV-LC40T850FL LED TV repairing.

SUPRA STV-LC40T850FL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC40T850FL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 16

SUPRA STV-LC32T810WL LED TV FLASH DUMP
Download Here

SUPRA STV-LC32T810WL LED TV

SUPRA STV-LC32T810WL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC32T810WL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC32T810WL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC32T810WL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC32T810WL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC32T810WL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC32T810WL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC32T810WL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: TP.VST59.P83
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: TC315F3E5-A
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC32T810WL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC32T810WL LED TV has the main board TP.VST59.P83 installed in it so the SPI Flash file backup saved from working board TP.VST59.P83. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59.P83 dump file is shared below for the SUPRA STV-LC32T810WL LED TV repairing.

SUPRA STV-LC32T810WL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC32T810WL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 13

SUPRA STV-LC24T810FL LED TV FLASH DUMP
Download Here

SUPRA STV-LC24T810FL LED TV

SUPRA STV-LC24T810FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC24T810FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC24T810FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC24T810FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC24T810FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC24T810FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC24T810FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC24T810FL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: T.MSD309.3D 11112
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: TB236F101-A
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC24T810FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC24T810FL LED TV has the main board T.MSD309.3D 11112 installed in it so the SPI Flash file backup saved from working board T.MSD309.3D 11112. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.3D 11112 dump file is shared below for the SUPRA STV-LC24T810FL LED TV repairing.

SUPRA STV-LC24T810FL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC24T810FL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 15

SUPRA STV-LC32T430WL LED TV FLASH DUMP
Download Here

SUPRA STV-LC32T430WL LED TV

SUPRA STV-LC32T430WL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC32T430WL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC32T430WL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC32T430WL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC32T430WL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC32T430WL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC32T430WL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC32T430WL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: TP.MS3463T.PB751
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: C320X16-E9-B (G01)
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC32T430WL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC32T430WL LED TV has the main board TP.MS3463T.PB751 installed in it so the SPI Flash file backup saved from working board TP.MS3463T.PB751. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463T.PB751 dump file is shared below for the SUPRA STV-LC32T430WL LED TV repairing.

SUPRA STV-LC32T430WL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC32T430WL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 285

SUPRA STV-LC32T410WL LED TV FLASH DUMP
Download Here

SUPRA STV-LC32T410WL LED TV

SUPRA STV-LC32T410WL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC32T410WL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC32T410WL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC32T410WL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC32T410WL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC32T410WL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC32T410WL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC32T410WL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: KDL32PS618AT
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: HV320WX2-206
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC32T410WL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC32T410WL LED TV has the main board KDL32PS618AT installed in it so the SPI Flash file backup saved from working board KDL32PS618AT. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. KDL32PS618AT dump file is shared below for the SUPRA STV-LC32T410WL LED TV repairing.

SUPRA STV-LC32T410WL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC32T410WL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 17

SUPRA STV-LC3239F LED TV FLASH DUMP
Download Here

SUPRA STV-LC3239F LED TV

SUPRA STV-LC3239F LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC3239F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC3239F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC3239F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC3239F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC3239F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC3239F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC3239F LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: CV182H-J
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: LTA320HN02
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC3239F LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC3239F LED TV has the main board CV182H-J installed in it so the SPI Flash file backup saved from working board CV182H-J. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV182H-J dump file is shared below for the SUPRA STV-LC3239F LED TV repairing.

SUPRA STV-LC3239F LED TV Software download free.

How to Download Free Software for SUPRA STV-LC3239F LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 18

SUPRA STV-LC39520FL LED TV FLASH DUMP
Download Here

SUPRA STV-LC39520FL LED TV

SUPRA STV-LC39520FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC39520FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC39520FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC39520FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC39520FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC39520FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC39520FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC39520FL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: TP.VST59.P83
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: V390HJ1-P02
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC39520FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC39520FL LED TV has the main board TP.VST59.P83 installed in it so the SPI Flash file backup saved from working board TP.VST59.P83. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59.P83 dump file is shared below for the SUPRA STV-LC39520FL LED TV repairing.

SUPRA STV-LC39520FL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC39520FL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/02/2023
0 15

SUPRA STV-LC32520WL LED TV FLASH DUMP
Download Here

SUPRA STV-LC32520WL LED TV

SUPRA STV-LC32520WL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC32520WL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC32520WL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC32520WL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC32520WL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC32520WL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC32520WL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC32520WL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: T.MS18VG.72
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: HV320WX2-201
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC32520WL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC32520WL LED TV has the main board T.MS18VG.72 installed in it so the SPI Flash file backup saved from working board T.MS18VG.72. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.72 dump file is shared below for the SUPRA STV-LC32520WL LED TV repairing.

SUPRA STV-LC32520WL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC32520WL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done