T.EME380.61

DNS E24D20 LED TV

DNS E24D20 LED TV Software file is shared for repairing purpose. If the DNS E24D20 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS E24D20 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS E24D20 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS E24D20 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS E24D20 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS E24D20 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS E24D20 LED TV:

• Make/Brand: DNS
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: DNS
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS E24D20 LED TV dump file is shared below for repairing the firmware problem. DNS E24D20 LED TV has the main board T.EME380.61 installed in it so the SPI Flash file backup saved from working board T.EME380.61. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.EME380.61 dump file is shared below for the DNS E24D20 LED TV repairing.

DNS E24D20 LED TV Software download free.

How to Download Free Software for DNS E24D20 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

DNS 24AE7000 LED TV

DNS 24AE7000 LED TV Software file is shared for repairing purpose. If the DNS 24AE7000 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS 24AE7000 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS 24AE7000 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS 24AE7000 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS 24AE7000 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS 24AE7000 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS 24AE7000 LED TV:

• Make/Brand: DNS
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: DNS
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS 24AE7000 LED TV dump file is shared below for repairing the firmware problem. DNS 24AE7000 LED TV has the main board T.EME380.61 installed in it so the SPI Flash file backup saved from working board T.EME380.61. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.EME380.61 dump file is shared below for the DNS 24AE7000 LED TV repairing.

DNS 24AE7000 LED TV Software download free.

How to Download Free Software for DNS 24AE7000 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

CHANGHONG LED22A0B LED TV

CHANGHONG LED22A0B LED TV Software file is shared for repairing purpose. If the CHANGHONG LED22A0B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the CHANGHONG LED22A0B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and CHANGHONG LED22A0B LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the CHANGHONG LED22A0B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in CHANGHONG LED22A0B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given CHANGHONG LED22A0B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications CHANGHONG LED22A0B LED TV:

• Make/Brand: CHANGHONG
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: CHANGHONG
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

CHANGHONG LED22A0B LED TV dump file is shared below for repairing the firmware problem. CHANGHONG LED22A0B LED TV has the main board T.EME380.61 installed in it so the SPI Flash file backup saved from working board T.EME380.61. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.EME380.61 dump file is shared below for the CHANGHONG LED22A0B LED TV repairing.

CHANGHONG LED22A0B LED TV Software download free.

How to Download Free Software for CHANGHONG LED22A0B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

CHANGHONG LED19T868 LED TV

CHANGHONG LED19T868 LED TV Software file is shared for repairing purpose. If the CHANGHONG LED19T868 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the CHANGHONG LED19T868 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and CHANGHONG LED19T868 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the CHANGHONG LED19T868 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in CHANGHONG LED19T868 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given CHANGHONG LED19T868 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications CHANGHONG LED19T868 LED TV:

• Make/Brand: CHANGHONG
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: CHANGHONG
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

CHANGHONG LED19T868 LED TV dump file is shared below for repairing the firmware problem. CHANGHONG LED19T868 LED TV has the main board T.EME380.61 installed in it so the SPI Flash file backup saved from working board T.EME380.61. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.EME380.61 dump file is shared below for the CHANGHONG LED19T868 LED TV repairing.

CHANGHONG LED19T868 LED TV Software download free.

How to Download Free Software for CHANGHONG LED19T868 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

HISENSE LHD24D33EU LED TV SOFTWARE

HISENSE LHD24D33EU LED TV software file is shared for repairing purpose. If the HISENSE LHD24D33EU LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then this software file can be loaded by USB. If the HISENSE LHD24D33EU LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and HISENSE LHD24D33EU LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the HISENSE LHD24D33EU LED TV are tested and found accurate then load software file, hope the issue will be resolved by installing this USB Boot Software.

For installing USB Boot file in HISENSE LHD24D33EU LED TV board, first of all save the backup if you have any programming device. This software file is compatible with HISENSE LHD24D33EU LED TV. USB Disk must be formatted with FAT32 system. Mostly new FAT 32 devices are not supported for USB Boot so, make sure that USB disk is compatible. Transfer the given software file into USB disk and plug in into USB port of HISENSE LHD24D33EU LED TV Mainboard and switch on. It will flash automatically. After Completion remove the USB disk and power on the TV. Hope TV will be normal now. If you have any problem by installing software then Read Here.

Technical Specifications HISENSE LHD24D33EU LED TV:

• Make/Brand: HISENSE
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type:
• Product User: HISENSE
• Product Model:

Special Note:

The attached software is USB Boot file and can be loaded by a USB Disk in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before installing software. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

DOWNLOAD LINK

Click for more LED TV Software

HISENSE LHD24W26CEU LED TV

HISENSE LHD24W26CEU LED TV flash dump file is shared for repairing purpose. If the HISENSE LHD24W26CEU LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the HISENSE LHD24W26CEU LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and HISENSE LHD24W26CEU LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the HISENSE LHD24W26CEU LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

For writing flash dump file in HISENSE LHD24W26CEU LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given HISENSE LHD24W26CEU LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications HISENSE LHD24W26CEU LED TV:

• Make/Brand: HISENSE
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: HISENSE
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

DOWNLOAD LINK

Click for more Flash Dumps TV

GOLDVISION GVLED19M1A TNT LED TV

GOLDVISION GVLED19M1A TNT LED TV flash dump file is shared for repairing purpose. If the GOLDVISION GVLED19M1A TNT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded.

If the GOLDVISION GVLED19M1A TNT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and GOLDVISION GVLED19M1A TNT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit.

In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the GOLDVISION GVLED19M1A TNT LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

For writing flash dump file in GOLDVISION GVLED19M1A TNT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given GOLDVISION GVLED19M1A TNT LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications GOLDVISION GVLED19M1A TNT LED TV:

• Make/Brand: GOLDVISION
• Main Board/Chassis: T.EME380.61
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: GOLDVISION
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

DOWNLOAD LINK

Click for more Flash Dumps TV