T.MS18VG.62B 11505

29/10/2023
0 10

RUBIN RB-24S2UF LED TV FLASH DUMP
RUBIN RB-24S2UF LED TV

RUBIN RB-24S2UF LED TV Software file is shared for repairing purpose. If the RUBIN RB-24S2UF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the RUBIN RB-24S2UF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and RUBIN RB-24S2UF LED TV is still dead then check the primary power circuit if found ok then test the sRUBINdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sRUBINdary voltage of the main board of the RUBIN RB-24S2UF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in RUBIN RB-24S2UF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given RUBIN RB-24S2UF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications RUBIN RB-24S2UF LED TV:
- Make/Brand: RUBIN
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: RUBIN
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

RUBIN RB-24S2UF LED TV dump file is shared below for repairing the firmware problem. RUBIN RB-24S2UF LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the RUBIN RB-24S2UF LED TV repairing.

RUBIN RB-24S2UF LED TV Software download free.

How to Download Free Software for RUBIN RB-24S2UF LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
14/10/2023
0 6

POLAR 55LTV6005 LED TV FLASH DUMP
POLAR 55LTV6005 LED TV

POLAR 55LTV6005 LED TV Software file is shared for repairing purpose. If the POLAR 55LTV6005 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR 55LTV6005 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR 55LTV6005 LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR 55LTV6005 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR 55LTV6005 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR 55LTV6005 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR 55LTV6005 LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR 55LTV6005 LED TV dump file is shared below for repairing the firmware problem. POLAR 55LTV6005 LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the POLAR 55LTV6005 LED TV repairing.

POLAR 55LTV6005 LED TV Software download free.

How to Download Free Software for POLAR 55LTV6005 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
06/08/2023
0 16

IZUMI TLE19H750B LED TV FLASH DUMP
IZUMI TLE19H750B LED TV

IZUMI TLE19H750B LED TV Software file is shared for repairing purpose. If the IZUMI TLE19H750B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE19H750B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE19H750B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE19H750B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE19H750B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE19H750B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE19H750B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE19H750B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE19H750B LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the IZUMI TLE19H750B LED TV repairing.

IZUMI TLE19H750B LED TV Software download free.

How to Download Free Software for IZUMI TLE19H750B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
17/07/2023
0 13

ERGO LE19D30 LED TV FLASH DUMP
ERGO LE19D30 LED TV

ERGO LE19D30 LED TV Software file is shared for repairing purpose. If the ERGO LE19D30 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE19D30 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE19D30 LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE19D30 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE19D30 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE19D30 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE19D30 LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE19D30 LED TV dump file is shared below for repairing the firmware problem. ERGO LE19D30 LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the ERGO LE19D30 LED TV repairing.

ERGO LE19D30 LED TV Software download free.

How to Download Free Software for ERGO LE19D30 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
10/07/2023
0 46

DNS E16A90 LED TV FLASH DUMP
DNS E16A90 LED TV

DNS E16A90 LED TV Software file is shared for repairing purpose. If the DNS E16A90 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS E16A90 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS E16A90 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS E16A90 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS E16A90 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS E16A90 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS E16A90 LED TV:
- Make/Brand: DNS
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DNS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS E16A90 LED TV dump file is shared below for repairing the firmware problem. DNS E16A90 LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the DNS E16A90 LED TV repairing.

DNS E16A90 LED TV Software download free.

How to Download Free Software for DNS E16A90 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/03/2023
0 17

BBK LEM2238F LED TV FLASH DUMP
BBK LEM2238F LED TV

BBK LEM2238F LED TV Software file is shared for repairing purpose. If the BBK LEM2238F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the BBK LEM2238F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and BBK LEM2238F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM2238F LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in BBK LEM2238F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM2238F LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications BBK LEM2238F LED TV:
- Make/Brand: BBK
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: BBK
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

BBK LEM2238F LED TV dump file is shared below for repairing the firmware problem. BBK LEM2238F LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the BBK LEM2238F LED TV repairing.

BBK LEM2238F LED TV Software download free.

How to Download Free Software for BBK LEM2238F LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/02/2023
0 15

AKAI LEA-24N20P LED TV FLASH DUMP
AKAI LEA-24N20P LED TV

AKAI LEA-24N20P LED TV Software file is shared for repairing purpose. If the AKAI LEA-24N20P LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKAI LEA-24N20P LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKAI LEA-24N20P LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-24N20P LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKAI LEA-24N20P LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-24N20P LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKAI LEA-24N20P LED TV:
- Make/Brand: AKAI
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: M240HW01
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKAI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKAI LEA-24N20P LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-24N20P LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the AKAI LEA-24N20P LED TV repairing.

AKAI LEA-24N20P LED TV Software download free.

How to Download Free Software for AKAI LEA-24N20P LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/02/2023
0 13

AKAI LEA-22L14G LED TV FLASH DUMP
AKAI LEA-22L14G LED TV

AKAI LEA-22L14G LED TV Software file is shared for repairing purpose. If the AKAI LEA-22L14G LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKAI LEA-22L14G LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKAI LEA-22L14G LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-22L14G LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKAI LEA-22L14G LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-22L14G LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKAI LEA-22L14G LED TV:
- Make/Brand: AKAI
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: M215HW03 V1
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKAI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKAI LEA-22L14G LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-22L14G LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the AKAI LEA-22L14G LED TV repairing.

AKAI LEA-22L14G LED TV Software download free.

How to Download Free Software for AKAI LEA-22L14G LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/02/2023
0 31

AKAI LEA-22E17P LED TV FLASH DUMP
AKAI LEA-22E17P LED TV

AKAI LEA-22E17P LED TV Software file is shared for repairing purpose. If the AKAI LEA-22E17P LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKAI LEA-22E17P LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKAI LEA-22E17P LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LEA-22E17P LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKAI LEA-22E17P LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LEA-22E17P LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKAI LEA-22E17P LED TV:
- Make/Brand: AKAI
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: CX215LEDM
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKAI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKAI LEA-22E17P LED TV dump file is shared below for repairing the firmware problem. AKAI LEA-22E17P LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the AKAI LEA-22E17P LED TV repairing.

AKAI LEA-22E17P LED TV Software download free.

How to Download Free Software for AKAI LEA-22E17P LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
06/02/2023
0 10

SUPRA STV-LC18250FL LED TV FLASH DUMP
SUPRA STV-LC18250FL LED TV

SUPRA STV-LC18250FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC18250FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC18250FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC18250FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC18250FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC18250FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC18250FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC18250FL LED TV:
- Make/Brand: SUPRA
- Main Board/Chassis: T.MS18VG.62B 11505
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: B173RW01 V.3
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SUPRA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC18250FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC18250FL LED TV has the main board T.MS18VG.62B 11505 installed in it so the SPI Flash file backup saved from working board T.MS18VG.62B 11505. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MS18VG.62B 11505 dump file is shared below for the SUPRA STV-LC18250FL LED TV repairing.

SUPRA STV-LC18250FL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC18250FL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

RUBIN RB-24S2UF LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications RUBIN RB-24S2UF LED TV:

About Mainboard:

POLAR 55LTV6005 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications POLAR 55LTV6005 LED TV:

About Mainboard:

IZUMI TLE19H750B LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications IZUMI TLE19H750B LED TV:

About Mainboard:

ERGO LE19D30 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications ERGO LE19D30 LED TV:

About Mainboard:

DNS E16A90 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DNS E16A90 LED TV:

About Mainboard:

BBK LEM2238F LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications BBK LEM2238F LED TV:

About Mainboard:

AKAI LEA-24N20P LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKAI LEA-24N20P LED TV:

About Mainboard:

AKAI LEA-22L14G LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKAI LEA-22L14G LED TV:

About Mainboard:

AKAI LEA-22E17P LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKAI LEA-22E17P LED TV:

About Mainboard:

SUPRA STV-LC18250FL LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SUPRA STV-LC18250FL LED TV:

About Mainboard:

Adblock Detected