T.MSD309.9B 10345

  • 21/01/2024
    0 20

    VITYAZ 32LCD861-5DC LED TV FLASH DUMP

    VITYAZ 32LCD861-5DC LED TV

    VITYAZ 32LCD861-5DC LED TV Software file is shared for repairing purpose. If the VITYAZ 32LCD861-5DC LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    VITYAZ 32LCD861-5DC

    Troubleshooting Guide:

    If the VITYAZ 32LCD861-5DC LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and VITYAZ 32LCD861-5DC LED TV is still dead then check the primary power circuit if found ok then test the sVITYAZdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sVITYAZdary voltage of the main board of the VITYAZ 32LCD861-5DC LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in VITYAZ 32LCD861-5DC LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VITYAZ 32LCD861-5DC LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications VITYAZ 32LCD861-5DC LED TV:
    • Make/Brand: VITYAZ
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: VITYAZ
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    VITYAZ 32LCD861-5DC LED TV dump file is shared below for repairing the firmware problem. VITYAZ 32LCD861-5DC LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the VITYAZ 32LCD861-5DC LED TV repairing.

    Download

    VITYAZ 32LCD861-5DC LED TV Software download free.

    How to Download Free Software for VITYAZ 32LCD861-5DC LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 06/08/2023
    0 23

    IZUMI TLE32D400B LED TV FLASH DUMP

    IZUMI TLE32D400B LED TV

    IZUMI TLE32D400B LED TV Software file is shared for repairing purpose. If the IZUMI TLE32D400B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    IZUMI TLE32D400B

    Troubleshooting Guide:

    If the IZUMI TLE32D400B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and IZUMI TLE32D400B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE32D400B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in IZUMI TLE32D400B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE32D400B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications IZUMI TLE32D400B LED TV:
    • Make/Brand: IZUMI
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: IZUMI
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    IZUMI TLE32D400B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE32D400B LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the IZUMI TLE32D400B LED TV repairing.

    Download

    IZUMI TLE32D400B LED TV Software download free.

    How to Download Free Software for IZUMI TLE32D400B LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 18/03/2023
    0 46

    BBK LEM3241FTD LED TV FLASH DUMP

    BBK LEM3241FTD LED TV

    BBK LEM3241FTD LED TV Software file is shared for repairing purpose. If the BBK LEM3241FTD LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3241FTD

    Troubleshooting Guide:

    If the BBK LEM3241FTD LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3241FTD LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3241FTD LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3241FTD LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3241FTD LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3241FTD LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3241FTD LED TV dump file is shared below for repairing the firmware problem. BBK LEM3241FTD LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the BBK LEM3241FTD LED TV repairing.

    Download
    BBK LEM3241FTD LED TV Software download free.

    How to Download Free Software for BBK LEM3241FTD LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 18/03/2023
    0 23

    BBK LEM3241FDT LED TV FLASH DUMP

    BBK LEM3241FDT LED TV

    BBK LEM3241FDT LED TV Software file is shared for repairing purpose. If the BBK LEM3241FDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    BBK LEM3241FDT

    Troubleshooting Guide:

    If the BBK LEM3241FDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and BBK LEM3241FDT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the BBK LEM3241FDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in BBK LEM3241FDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given BBK LEM3241FDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications BBK LEM3241FDT LED TV:
    • Make/Brand: BBK
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: BBK
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    BBK LEM3241FDT LED TV dump file is shared below for repairing the firmware problem. BBK LEM3241FDT LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the BBK LEM3241FDT LED TV repairing.

    Download
    BBK LEM3241FDT LED TV Software download free.

    How to Download Free Software for BBK LEM3241FDT LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 07/02/2023
    0 23

    SUPRA STV-LC3245LF LED TV FLASH DUMP

    SUPRA STV-LC3245LF LED TV

    SUPRA STV-LC3245LF LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC3245LF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SUPRA STV-LC3245LF

    Troubleshooting Guide:

    If the SUPRA STV-LC3245LF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SUPRA STV-LC3245LF LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC3245LF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SUPRA STV-LC3245LF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC3245LF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SUPRA STV-LC3245LF LED TV:
    • Make/Brand: SUPRA
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: TC315F1H2
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SUPRA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SUPRA STV-LC3245LF LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC3245LF LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the SUPRA STV-LC3245LF LED TV repairing.

    Download
    SUPRA STV-LC3245LF LED TV Software download free.

    How to Download Free Software for SUPRA STV-LC3245LF LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 07/02/2023
    0 19

    SUPRA STV-LC4225LF LED TV FLASH DUMP

    SUPRA STV-LC4225LF LED TV

    SUPRA STV-LC4225LF LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC4225LF LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SUPRA STV-LC4225LF

    Troubleshooting Guide:

    If the SUPRA STV-LC4225LF LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SUPRA STV-LC4225LF LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC4225LF LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SUPRA STV-LC4225LF LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC4225LF LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SUPRA STV-LC4225LF LED TV:
    • Make/Brand: SUPRA
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SUPRA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SUPRA STV-LC4225LF LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC4225LF LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the SUPRA STV-LC4225LF LED TV repairing.

    Download
    SUPRA STV-LC4225LF LED TV Software download free.

    How to Download Free Software for SUPRA STV-LC4225LF LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 07/02/2023
    0 13

    SUPRA STV-LC46T810FL LED TV FLASH DUMP

    SUPRA STV-LC46T810FL LED TV

    SUPRA STV-LC46T810FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC46T810FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SUPRA STV-LC46T810FL

    Troubleshooting Guide:

    If the SUPRA STV-LC46T810FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SUPRA STV-LC46T810FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC46T810FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SUPRA STV-LC46T810FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC46T810FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SUPRA STV-LC46T810FL LED TV:
    • Make/Brand: SUPRA
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: 1080p Full HD, 1920×1080
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SUPRA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SUPRA STV-LC46T810FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC46T810FL LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the SUPRA STV-LC46T810FL LED TV repairing.

    Download
    SUPRA STV-LC46T810FL LED TV Software download free.

    How to Download Free Software for SUPRA STV-LC46T810FL LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 07/02/2023
    0 384

    SUPRA STV-LC46T820FL LED TV FLASH DUMP

    SUPRA STV-LC46T820FL LED TV

    SUPRA STV-LC46T820FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC46T820FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SUPRA STV-LC46T820FL

    Troubleshooting Guide:

    If the SUPRA STV-LC46T820FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SUPRA STV-LC46T820FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC46T820FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SUPRA STV-LC46T820FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC46T820FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SUPRA STV-LC46T820FL LED TV:
    • Make/Brand: SUPRA
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: TC460F109-B
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SUPRA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SUPRA STV-LC46T820FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC46T820FL LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the SUPRA STV-LC46T820FL LED TV repairing.

    Download
    SUPRA STV-LC46T820FL LED TV Software download free.

    How to Download Free Software for SUPRA STV-LC46T820FL LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 07/02/2023
    0 18

    SUPRA STV-LC39T820FL LED TV FLASH DUMP

    SUPRA STV-LC39T820FL LED TV

    SUPRA STV-LC39T820FL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC39T820FL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SUPRA STV-LC39T820FL

    Troubleshooting Guide:

    If the SUPRA STV-LC39T820FL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SUPRA STV-LC39T820FL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC39T820FL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SUPRA STV-LC39T820FL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC39T820FL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SUPRA STV-LC39T820FL LED TV:
    • Make/Brand: SUPRA
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: TC390FP01-B
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SUPRA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SUPRA STV-LC39T820FL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC39T820FL LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the SUPRA STV-LC39T820FL LED TV repairing.

    Download
    SUPRA STV-LC39T820FL LED TV Software download free.

    How to Download Free Software for SUPRA STV-LC39T820FL LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

  • 05/02/2023
    0 18

    SUPRA STV-LC2625LD LED TV FLASH DUMP

    SUPRA STV-LC2625LD LED TV

    SUPRA STV-LC2625LD LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC2625LD LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

    SUPRA STV-LC2625LD

    Troubleshooting Guide:

    If the SUPRA STV-LC2625LD LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

    If both are found ok and SUPRA STV-LC2625LD LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC2625LD LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

    Installation Instructions:

    For writing Software file in SUPRA STV-LC2625LD LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC2625LD LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications SUPRA STV-LC2625LD LED TV:
    • Make/Brand: SUPRA
    • Main Board/Chassis: T.MSD309.9B 10345
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info: TC260F103
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: SUPRA
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    Click for more Softwares TV

    About Mainboard:

    SUPRA STV-LC2625LD LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC2625LD LED TV has the main board T.MSD309.9B 10345 installed in it so the SPI Flash file backup saved from working board T.MSD309.9B 10345. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.MSD309.9B 10345 dump file is shared below for the SUPRA STV-LC2625LD LED TV repairing.

    Download
    SUPRA STV-LC2625LD LED TV Software download free.

    How to Download Free Software for SUPRA STV-LC2625LD LED TV:

    1. Click on the file part or Download Link, New Tab will open
    2. Click on Free Download or Premium Download as per your account type
    3. Check I’m not robot and wait for countdown timer to end
    4. Click on Create Download Link
    5. Ignore Popups and wait for Preparing Download Link
    6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

Next page
error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly