T.SIS231.T65

RUBIN RB-22SE9FT2C LED TV

RUBIN RB-22SE9FT2C LED TV Software file is shared for repairing purpose. If the RUBIN RB-22SE9FT2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the RUBIN RB-22SE9FT2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and RUBIN RB-22SE9FT2C LED TV is still dead then check the primary power circuit if found ok then test the sRUBINdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sRUBINdary voltage of the main board of the RUBIN RB-22SE9FT2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in RUBIN RB-22SE9FT2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given RUBIN RB-22SE9FT2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications RUBIN RB-22SE9FT2C LED TV:

• Make/Brand: RUBIN
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: RUBIN
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

RUBIN RB-22SE9FT2C LED TV dump file is shared below for repairing the firmware problem. RUBIN RB-22SE9FT2C LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the RUBIN RB-22SE9FT2C LED TV repairing.

RUBIN RB-22SE9FT2C LED TV Software download free.

How to Download Free Software for RUBIN RB-22SE9FT2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

RUBIN RB-22SE1FT2C LED TV

RUBIN RB-22SE1FT2C LED TV Software file is shared for repairing purpose. If the RUBIN RB-22SE1FT2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the RUBIN RB-22SE1FT2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and RUBIN RB-22SE1FT2C LED TV is still dead then check the primary power circuit if found ok then test the sRUBINdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sRUBINdary voltage of the main board of the RUBIN RB-22SE1FT2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in RUBIN RB-22SE1FT2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given RUBIN RB-22SE1FT2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications RUBIN RB-22SE1FT2C LED TV:

• Make/Brand: RUBIN
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: RUBIN
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

RUBIN RB-22SE1FT2C LED TV dump file is shared below for repairing the firmware problem. RUBIN RB-22SE1FT2C LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the RUBIN RB-22SE1FT2C LED TV repairing.

RUBIN RB-22SE1FT2C LED TV Software download free.

How to Download Free Software for RUBIN RB-22SE1FT2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

IZUMI TLE-19D330B LED TV

IZUMI TLE-19D330B LED TV Software file is shared for repairing purpose. If the IZUMI TLE-19D330B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

 

Troubleshooting Guide:

If the IZUMI TLE-19D330B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE-19D330B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE-19D330B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE-19D330B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE-19D330B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE-19D330B LED TV:

• Make/Brand: IZUMI
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: IZUMI
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE-19D330B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE-19D330B LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the IZUMI TLE-19D330B LED TV repairing.

IZUMI TLE-19D330B LED TV Software download free.

How to Download Free Software for IZUMI TLE-19D330B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

DNS 22AE7000 LED TV

DNS 22AE7000 LED TV Software file is shared for repairing purpose. If the DNS 22AE7000 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS 22AE7000 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS 22AE7000 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS 22AE7000 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS 22AE7000 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS 22AE7000 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS 22AE7000 LED TV:

• Make/Brand: DNS
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: DNS
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS 22AE7000 LED TV dump file is shared below for repairing the firmware problem. DNS 22AE7000 LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the DNS 22AE7000 LED TV repairing.

DNS 22AE7000 LED TV Software download free.

How to Download Free Software for DNS 22AE7000 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

DNS M24DM8 LED TV

DNS M24DM8 LED TV Software file is shared for repairing purpose. If the DNS M24DM8 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS M24DM8 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS M24DM8 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS M24DM8 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS M24DM8 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS M24DM8 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS M24DM8 LED TV:

• Make/Brand: DNS
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: DNS
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS M24DM8 LED TV dump file is shared below for repairing the firmware problem. DNS M24DM8 LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the DNS M24DM8 LED TV repairing.

DNS M24DM8 LED TV Software download free.

How to Download Free Software for DNS M24DM8 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

DNS M24M8 LED TV

DNS M24M8 LED TV Software file is shared for repairing purpose. If the DNS M24M8 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS M24M8 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS M24M8 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS M24M8 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS M24M8 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS M24M8 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS M24M8 LED TV:

• Make/Brand: DNS
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: DNS
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS M24M8 LED TV dump file is shared below for repairing the firmware problem. DNS M24M8 LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the DNS M24M8 LED TV repairing.

DNS M24M8 LED TV Software download free.

How to Download Free Software for DNS M24M8 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

DEXP H19B3100EE LED TV

DEXP H19B3100EE LED TV Software file is shared for repairing purpose. If the DEXP H19B3100EE LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DEXP H19B3100EE LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DEXP H19B3100EE LED TV is still dead then check the primary power circuit if found ok then test the sDEXPdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDEXPdary voltage of the main board of the DEXP H19B3100EE LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DEXP H19B3100EE LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DEXP H19B3100EE LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DEXP H19B3100EE LED TV:

• Make/Brand: DEXP
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: DEXP
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DEXP H19B3100EE LED TV dump file is shared below for repairing the firmware problem. DEXP H19B3100EE LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the DEXP H19B3100EE LED TV repairing.

DEXP H19B3100EE LED TV Software download free.

How to Download Free Software for DEXP H19B3100EE LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

SUPRA STV-LC19T551WL LED TV

SUPRA STV-LC19T551WL LED TV Software file is shared for repairing purpose. If the SUPRA STV-LC19T551WL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SUPRA STV-LC19T551WL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SUPRA STV-LC19T551WL LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the SUPRA STV-LC19T551WL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SUPRA STV-LC19T551WL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SUPRA STV-LC19T551WL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SUPRA STV-LC19T551WL LED TV:

• Make/Brand: SUPRA
• Main Board/Chassis: T.SIS231.T65
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info: HM185WX3-400
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: SUPRA
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SUPRA STV-LC19T551WL LED TV dump file is shared below for repairing the firmware problem. SUPRA STV-LC19T551WL LED TV has the main board T.SIS231.T65 installed in it so the SPI Flash file backup saved from working board T.SIS231.T65. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.SIS231.T65 dump file is shared below for the SUPRA STV-LC19T551WL LED TV repairing.

SUPRA STV-LC19T551WL LED TV Software download free.

How to Download Free Software for SUPRA STV-LC19T551WL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done