T-VST29.A3B

04/11/2023
0 1,089

SATURN LED19HD300U LED TV FLASH DUMP
SATURN LED19HD300U LED TV

SATURN LED19HD300U LED TV Software file is shared for repairing purpose. If the SATURN LED19HD300U LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SATURN LED19HD300U LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SATURN LED19HD300U LED TV is still dead then check the primary power circuit if found ok then test the sSATURNdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSATURNdary voltage of the main board of the SATURN LED19HD300U LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SATURN LED19HD300U LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SATURN LED19HD300U LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SATURN LED19HD300U LED TV:
- Make/Brand: SATURN
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SATURN
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SATURN LED19HD300U LED TV dump file is shared below for repairing the firmware problem. SATURN LED19HD300U LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the SATURN LED19HD300U LED TV repairing.

SATURN LED19HD300U LED TV Software download free.

How to Download Free Software for SATURN LED19HD300U LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
03/09/2023
0 42

LIBERTON LED 1680AWUV LED TV FLASH DUMP
LIBERTON LED 1680AWUV LED TV

LIBERTON LED 1680AWUV LED TV Software file is shared for repairing purpose. If the LIBERTON LED 1680AWUV LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the LIBERTON LED 1680AWUV LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and LIBERTON LED 1680AWUV LED TV is still dead then check the primary power circuit if found ok then test the sLIBERTONdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sLIBERTONdary voltage of the main board of the LIBERTON LED 1680AWUV LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in LIBERTON LED 1680AWUV LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given LIBERTON LED 1680AWUV LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications LIBERTON LED 1680AWUV LED TV:
- Make/Brand: LIBERTON
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: LIBERTON
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

LIBERTON LED 1680AWUV LED TV dump file is shared below for repairing the firmware problem. LIBERTON LED 1680AWUV LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the LIBERTON LED 1680AWUV LED TV repairing.

LIBERTON LED 1680AWUV LED TV Software download free.

How to Download Free Software for LIBERTON LED 1680AWUV LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
06/08/2023
0 12

IZUMI TLE19H310B LED TV FLASH DUMP
IZUMI TLE19H310B LED TV

IZUMI TLE19H310B LED TV Software file is shared for repairing purpose. If the IZUMI TLE19H310B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE19H310B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE19H310B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE19H310B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE19H310B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE19H310B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE19H310B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE19H310B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE19H310B LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the IZUMI TLE19H310B LED TV repairing.

IZUMI TLE19H310B LED TV Software download free.

How to Download Free Software for IZUMI TLE19H310B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
03/08/2023
0 9

IZUMI TLE19H103B LED TV FLASH DUMP
IZUMI TLE19H103B LED TV

IZUMI TLE19H103B LED TV Software file is shared for repairing purpose. If the IZUMI TLE19H103B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE19H103B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE19H103B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE19H103B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE19H103B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE19H103B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE19H103B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE19H103B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE19H103B LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the IZUMI TLE19H103B LED TV repairing.

IZUMI TLE19H103B LED TV Software download free.

How to Download Free Software for IZUMI TLE19H103B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
24/06/2023
0 11

DIGITAL DLE-2227 LED TV FLASH DUMP
DIGITAL DLE-2227 LED TV

DIGITAL DLE-2227 LED TV Software file is shared for repairing purpose. If the DIGITAL DLE-2227 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DIGITAL DLE-2227 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DIGITAL DLE-2227 LED TV is still dead then check the primary power circuit if found ok then test the sDIGITALdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDIGITALdary voltage of the main board of the DIGITAL DLE-2227 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DIGITAL DLE-2227 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DIGITAL DLE-2227 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DIGITAL DLE-2227 LED TV:
- Make/Brand: DIGITAL
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DIGITAL
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DIGITAL DLE-2227 LED TV dump file is shared below for repairing the firmware problem. DIGITAL DLE-2227 LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the DIGITAL DLE-2227 LED TV repairing.

DIGITAL DLE-2227 LED TV Software download free.

How to Download Free Software for DIGITAL DLE-2227 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
27/03/2023
0 21

CHANGHONG E16A100A LED TV FLASH DUMP
CHANGHONG E16A100A LED TV

CHANGHONG E16A100A LED TV Software file is shared for repairing purpose. If the CHANGHONG E16A100A LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the CHANGHONG E16A100A LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and CHANGHONG E16A100A LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the CHANGHONG E16A100A LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in CHANGHONG E16A100A LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given CHANGHONG E16A100A LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications CHANGHONG E16A100A LED TV:
- Make/Brand: CHANGHONG
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: CHANGHONG
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

CHANGHONG E16A100A LED TV dump file is shared below for repairing the firmware problem. CHANGHONG E16A100A LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the CHANGHONG E16A100A LED TV repairing.

CHANGHONG E16A100A LED TV Software download free.

How to Download Free Software for CHANGHONG E16A100A LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
27/03/2023
0 17

CHANGHONG E19A100A LED TV FLASH DUMP
CHANGHONG E19A100A LED TV

CHANGHONG E19A100A LED TV Software file is shared for repairing purpose. If the CHANGHONG E19A100A LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the CHANGHONG E19A100A LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and CHANGHONG E19A100A LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the CHANGHONG E19A100A LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in CHANGHONG E19A100A LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given CHANGHONG E19A100A LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications CHANGHONG E19A100A LED TV:
- Make/Brand: CHANGHONG
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: CHANGHONG
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

CHANGHONG E19A100A LED TV dump file is shared below for repairing the firmware problem. CHANGHONG E19A100A LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the CHANGHONG E19A100A LED TV repairing.

CHANGHONG E19A100A LED TV Software download free.

How to Download Free Software for CHANGHONG E19A100A LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
27/03/2023
0 23

CHANGHONG LED19B1000 LED TV FLASH DUMP
CHANGHONG LED19B1000 LED TV

CHANGHONG LED19B1000 LED TV Software file is shared for repairing purpose. If the CHANGHONG LED19B1000 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the CHANGHONG LED19B1000 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and CHANGHONG LED19B1000 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the CHANGHONG LED19B1000 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in CHANGHONG LED19B1000 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given CHANGHONG LED19B1000 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications CHANGHONG LED19B1000 LED TV:
- Make/Brand: CHANGHONG
- Main Board/Chassis: T.VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: CHANGHONG
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

CHANGHONG LED19B1000 LED TV dump file is shared below for repairing the firmware problem. CHANGHONG LED19B1000 LED TV has the main board T.VST29.A3B installed in it so the SPI Flash file backup saved from working board T.VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T.VST29.A3B dump file is shared below for the CHANGHONG LED19B1000 LED TV repairing.

CHANGHONG LED19B1000 LED TV Software download free.

How to Download Free Software for CHANGHONG LED19B1000 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/02/2023
0 18

AKAI LTA-15A15M LED TV FLASH DUMP
AKAI LTA-15A15M LED TV

AKAI LTA-15A15M LED TV Software file is shared for repairing purpose. If the AKAI LTA-15A15M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the AKAI LTA-15A15M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and AKAI LTA-15A15M LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the AKAI LTA-15A15M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in AKAI LTA-15A15M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given AKAI LTA-15A15M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications AKAI LTA-15A15M LED TV:
- Make/Brand: AKAI
- Main Board/Chassis: T-VST29.A3B
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info: HV150UX2-100
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: AKAI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

AKAI LTA-15A15M LED TV dump file is shared below for repairing the firmware problem. AKAI LTA-15A15M LED TV has the main board T-VST29.A3B installed in it so the SPI Flash file backup saved from working board T-VST29.A3B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. T-VST29.A3B dump file is shared below for the AKAI LTA-15A15M LED TV repairing.

AKAI LTA-15A15M LED TV Software download free.

How to Download Free Software for AKAI LTA-15A15M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

SATURN LED19HD300U LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications SATURN LED19HD300U LED TV:

About Mainboard:

LIBERTON LED 1680AWUV LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications LIBERTON LED 1680AWUV LED TV:

About Mainboard:

IZUMI TLE19H310B LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications IZUMI TLE19H310B LED TV:

About Mainboard:

IZUMI TLE19H103B LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications IZUMI TLE19H103B LED TV:

About Mainboard:

DIGITAL DLE-2227 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DIGITAL DLE-2227 LED TV:

About Mainboard:

CHANGHONG E16A100A LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications CHANGHONG E16A100A LED TV:

About Mainboard:

CHANGHONG E19A100A LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications CHANGHONG E19A100A LED TV:

About Mainboard:

CHANGHONG LED19B1000 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications CHANGHONG LED19B1000 LED TV:

About Mainboard:

AKAI LTA-15A15M LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications AKAI LTA-15A15M LED TV:

About Mainboard:

Adblock Detected