TOSHIBA Update Software

TOSHIBA 50L2300ZE LED TV

TOSHIBA 50L2300ZE LED TV Software file is shared for repairing purpose. If the TOSHIBA 50L2300ZE LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 50L2300ZE LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 50L2300ZE LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 50L2300ZE LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 50L2300ZE LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 50L2300ZE LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 50L2300ZE LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 50L2300ZE
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 50L2300ZE LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 50L2300ZE LED TV has the main board 50L2300ZE installed in it so the SPI Flash file backup saved from working board 50L2300ZE. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 50L2300ZE dump file is shared below for the TOSHIBA 50L2300ZE LED TV repairing.

How to Download Free Software for TOSHIBA 50L2300ZE LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 32P2305ZE LED TV

TOSHIBA 32P2305ZE LED TV Software file is shared for repairing purpose. If the TOSHIBA 32P2305ZE LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 32P2305ZE LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 32P2305ZE LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 32P2305ZE LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 32P2305ZE LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 32P2305ZE LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 32P2305ZE LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 32P2305ZE
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 32P2305ZE LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 32P2305ZE LED TV has the main board 32P2305ZE installed in it so the SPI Flash file backup saved from working board 32P2305ZE. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 32P2305ZE dump file is shared below for the TOSHIBA 32P2305ZE LED TV repairing.

How to Download Free Software for TOSHIBA 32P2305ZE LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 40BV701B LED TV

TOSHIBA 40BV701B LED TV Software file is shared for repairing purpose. If the TOSHIBA 40BV701B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 40BV701B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 40BV701B LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 40BV701B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 40BV701B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 40BV701B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 40BV701B LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 40BV701B
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 40BV701B LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 40BV701B LED TV has the main board 40BV701B installed in it so the SPI Flash file backup saved from working board 40BV701B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 40BV701B dump file is shared below for the TOSHIBA 40BV701B LED TV repairing.

How to Download Free Software for TOSHIBA 40BV701B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 32BV502B LED TV

TOSHIBA 32BV502B LED TV Software file is shared for repairing purpose. If the TOSHIBA 32BV502B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 32BV502B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 32BV502B LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 32BV502B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 32BV502B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 32BV502B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 32BV502B LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 32BV502B
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 32BV502B LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 32BV502B LED TV has the main board 32BV502B installed in it so the SPI Flash file backup saved from working board 32BV502B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 32BV502B dump file is shared below for the TOSHIBA 32BV502B LED TV repairing.

How to Download Free Software for TOSHIBA 32BV502B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 24P2400EA LED TV

TOSHIBA 24P2400EA LED TV Software file is shared for repairing purpose. If the TOSHIBA 24P2400EA LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 24P2400EA LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 24P2400EA LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 24P2400EA LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 24P2400EA LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 24P2400EA LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 24P2400EA LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 24P2400EA
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 24P2400EA LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 24P2400EA LED TV has the main board 24P2400EA installed in it so the SPI Flash file backup saved from working board 24P2400EA. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 24P2400EA dump file is shared below for the TOSHIBA 24P2400EA LED TV repairing.

How to Download Free Software for TOSHIBA 24P2400EA LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 22L133G LED TV

TOSHIBA 22L133G LED TV Software file is shared for repairing purpose. If the TOSHIBA 22L133G LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 22L133G LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 22L133G LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 22L133G LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 22L133G LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 22L133G LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 22L133G LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 22L133G
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 22L133G LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 22L133G LED TV has the main board 22L133G installed in it so the SPI Flash file backup saved from working board 22L133G. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 22L133G dump file is shared below for the TOSHIBA 22L133G LED TV repairing.

How to Download Free Software for TOSHIBA 22L133G LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 32W1333B LED TV

TOSHIBA 32W1333B LED TV Software file is shared for repairing purpose. If the TOSHIBA 32W1333B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 32W1333B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 32W1333B LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 32W1333B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 32W1333B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 32W1333B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 32W1333B LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 32W1333B
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 32W1333B LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 32W1333B LED TV has the main board 32W1333B installed in it so the SPI Flash file backup saved from working board 32W1333B. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 32W1333B dump file is shared below for the TOSHIBA 32W1333B LED TV repairing.

How to Download Free Software for TOSHIBA 32W1333B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 40L1333DG LED TV

TOSHIBA 40L1333DG LED TV Software file is shared for repairing purpose. If the TOSHIBA 40L1333DG LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 40L1333DG LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 40L1333DG LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 40L1333DG LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 40L1333DG LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 40L1333DG LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 40L1333DG LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 40L1333DG
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 40L1333DG LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 40L1333DG LED TV has the main board 40L1333DG installed in it so the SPI Flash file backup saved from working board 40L1333DG. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 40L1333DG dump file is shared below for the TOSHIBA 40L1333DG LED TV repairing.

How to Download Free Software for TOSHIBA 40L1333DG LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 32PU200V LED TV

TOSHIBA 32PU200V LED TV Software file is shared for repairing purpose. If the TOSHIBA 32PU200V LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 32PU200V LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 32PU200V LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 32PU200V LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 32PU200V LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 32PU200V LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 32PU200V LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 32PU200V
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 32PU200V LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 32PU200V LED TV has the main board 32PU200V installed in it so the SPI Flash file backup saved from working board 32PU200V. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 32PU200V dump file is shared below for the TOSHIBA 32PU200V LED TV repairing.

How to Download Free Software for TOSHIBA 32PU200V LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

TOSHIBA 32L1334DG LED TV

TOSHIBA 32L1334DG LED TV Software file is shared for repairing purpose. If the TOSHIBA 32L1334DG LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the TOSHIBA 32L1334DG LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and TOSHIBA 32L1334DG LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the TOSHIBA 32L1334DG LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in TOSHIBA 32L1334DG LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given TOSHIBA 32L1334DG LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications TOSHIBA 32L1334DG LED TV:

• Make/Brand: Toshiba
• Main Board/Chassis: 32L1334DG
• Board Type:
• Power Source:
• Rated Power Consumption:
• Panel Info:
• T-CON:
• Screen Resolution:
• Main Processor/Chipset:
• SPI Flash:
• Tuner:
• Firmware Type: SPI Dump
• Product User: Toshiba
• Product Model:
• Factory Code:

Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

TOSHIBA 32L1334DG LED TV dump file is shared below for repairing the firmware problem. TOSHIBA 32L1334DG LED TV has the main board 32L1334DG installed in it so the SPI Flash file backup saved from working board 32L1334DG. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 32L1334DG dump file is shared below for the TOSHIBA 32L1334DG LED TV repairing.

How to Download Free Software for TOSHIBA 32L1334DG LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done