TP.MS3463S.PB801

05/10/2023
0 1,936

ORION OLT-32902 LED TV FLASH DUMP
ORION OLT-32902 LED TV

ORION OLT-32902 LED TV Software file is shared for repairing purpose. If the ORION OLT-32902 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ORION OLT-32902 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ORION OLT-32902 LED TV is still dead then check the primary power circuit if found ok then test the sORIONdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sORIONdary voltage of the main board of the ORION OLT-32902 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ORION OLT-32902 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ORION OLT-32902 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ORION OLT-32902 LED TV:
- Make/Brand: ORION
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ORION
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ORION OLT-32902 LED TV dump file is shared below for repairing the firmware problem. ORION OLT-32902 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ORION OLT-32902 LED TV repairing.

ORION OLT-32902 LED TV Software download free.

How to Download Free Software for ORION OLT-32902 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
24/09/2023
0 18

OKEAN HD-28J2201 LED TV FLASH DUMP
OKEAN HD-28J2201 LED TV

OKEAN HD-28J2201 LED TV Software file is shared for repairing purpose. If the OKEAN HD-28J2201 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the OKEAN HD-28J2201 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and OKEAN HD-28J2201 LED TV is still dead then check the primary power circuit if found ok then test the sOKEANdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sOKEANdary voltage of the main board of the OKEAN HD-28J2201 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in OKEAN HD-28J2201 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given OKEAN HD-28J2201 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications OKEAN HD-28J2201 LED TV:
- Make/Brand: OKEAN
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: OKEAN
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

OKEAN HD-28J2201 LED TV dump file is shared below for repairing the firmware problem. OKEAN HD-28J2201 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the OKEAN HD-28J2201 LED TV repairing.

OKEAN HD-28J2201 LED TV Software download free.

How to Download Free Software for OKEAN HD-28J2201 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
03/09/2023
0 22

LIBERTON D-LED 3203DBT2 LED TV DUMP
LIBERTON D-LED 3203DBT2 LED TV

LIBERTON D-LED 3203DBT2 LED TV Software file is shared for repairing purpose. If the LIBERTON D-LED 3203DBT2 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the LIBERTON D-LED 3203DBT2 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and LIBERTON D-LED 3203DBT2 LED TV is still dead then check the primary power circuit if found ok then test the sLIBERTONdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sLIBERTONdary voltage of the main board of the LIBERTON D-LED 3203DBT2 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in LIBERTON D-LED 3203DBT2 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given LIBERTON D-LED 3203DBT2 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications LIBERTON D-LED 3203DBT2 LED TV:
- Make/Brand: LIBERTON
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: LIBERTON
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

LIBERTON D-LED 3203DBT2 LED TV dump file is shared below for repairing the firmware problem. LIBERTON D-LED 3203DBT2 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the LIBERTON D-LED 3203DBT2 LED TV repairing.

LIBERTON D-LED 3203DBT2 LED TV Software download free.

How to Download Free Software for LIBERTON D-LED 3203DBT2 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/07/2023
0 129

ERGO LE28CT5000AK LED TV FLASH DUMP
ERGO LE28CT5000AK LED TV

ERGO LE28CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE28CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE28CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE28CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE28CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE28CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE28CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE28CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE28CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE28CT5000AK LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ERGO LE28CT5000AK LED TV repairing.

ERGO LE28CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE28CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/07/2023
0 12

ERGO LE43CT2000AK LED TV FLASH DUMP
ERGO LE43CT2000AK LED TV

ERGO LE43CT2000AK LED TV Software file is shared for repairing purpose. If the ERGO LE43CT2000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE43CT2000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE43CT2000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE43CT2000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE43CT2000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE43CT2000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE43CT2000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE43CT2000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE43CT2000AK LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ERGO LE43CT2000AK LED TV repairing.

ERGO LE43CT2000AK LED TV Software download free.

How to Download Free Software for ERGO LE43CT2000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/07/2023
0 19

ERGO LE32CT2000AK LED TV FLASH DUMP
ERGO LE32CT2000AK LED TV

ERGO LE32CT2000AK LED TV Software file is shared for repairing purpose. If the ERGO LE32CT2000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE32CT2000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE32CT2000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE32CT2000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE32CT2000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE32CT2000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE32CT2000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE32CT2000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE32CT2000AK LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ERGO LE32CT2000AK LED TV repairing.

ERGO LE32CT2000AK LED TV Software download free.

How to Download Free Software for ERGO LE32CT2000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
16/07/2023
0 31

ELENBERG 42DF4330 LED TV FLASH DUMP
ELENBERG 42DF4330 LED TV

ELENBERG 42DF4330 LED TV Software file is shared for repairing purpose. If the ELENBERG 42DF4330 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ELENBERG 42DF4330 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ELENBERG 42DF4330 LED TV is still dead then check the primary power circuit if found ok then test the sELENBERGdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sELENBERGdary voltage of the main board of the ELENBERG 42DF4330 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ELENBERG 42DF4330 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ELENBERG 42DF4330 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ELENBERG 42DF4330 LED TV:
- Make/Brand: ELENBERG
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ELENBERG
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ELENBERG 42DF4330 LED TV dump file is shared below for repairing the firmware problem. ELENBERG 42DF4330 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ELENBERG 42DF4330 LED TV repairing.

ELENBERG 42DF4330 LED TV Software download free.

How to Download Free Software for ELENBERG 42DF4330 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
16/07/2023
0 11

ELENBERG 32DH4330 LED TV FLASH DUMP
ELENBERG 32DH4330 LED TV

ELENBERG 32DH4330 LED TV Software file is shared for repairing purpose. If the ELENBERG 32DH4330 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ELENBERG 32DH4330 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ELENBERG 32DH4330 LED TV is still dead then check the primary power circuit if found ok then test the sELENBERGdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sELENBERGdary voltage of the main board of the ELENBERG 32DH4330 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ELENBERG 32DH4330 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ELENBERG 32DH4330 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ELENBERG 32DH4330 LED TV:
- Make/Brand: ELENBERG
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ELENBERG
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ELENBERG 32DH4330 LED TV dump file is shared below for repairing the firmware problem. ELENBERG 32DH4330 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ELENBERG 32DH4330 LED TV repairing.

ELENBERG 32DH4330 LED TV Software download free.

How to Download Free Software for ELENBERG 32DH4330 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/07/2023
0 16

DOFFLER 43CF59 LED TV FLASH DUMP
DOFFLER 43CF59 LED TV

DOFFLER 43CF59 LED TV Software file is shared for repairing purpose. If the DOFFLER 43CF59 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DOFFLER 43CF59 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DOFFLER 43CF59 LED TV is still dead then check the primary power circuit if found ok then test the sDOFFLERdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDOFFLERdary voltage of the main board of the DOFFLER 43CF59 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DOFFLER 43CF59 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DOFFLER 43CF59 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DOFFLER 43CF59 LED TV:
- Make/Brand: DOFFLER
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DOFFLER
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DOFFLER 43CF59 LED TV dump file is shared below for repairing the firmware problem. DOFFLER 43CF59 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the DOFFLER 43CF59 LED TV repairing.

DOFFLER 43CF59 LED TV Software download free.

How to Download Free Software for DOFFLER 43CF59 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
12/07/2023
0 10

DOFFLER 40CF59 LED TV FLASH DUMP
DOFFLER 40CF59 LED TV

DOFFLER 40CF59 LED TV Software file is shared for repairing purpose. If the DOFFLER 40CF59 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DOFFLER 40CF59 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DOFFLER 40CF59 LED TV is still dead then check the primary power circuit if found ok then test the sDOFFLERdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDOFFLERdary voltage of the main board of the DOFFLER 40CF59 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DOFFLER 40CF59 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DOFFLER 40CF59 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DOFFLER 40CF59 LED TV:
- Make/Brand: DOFFLER
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DOFFLER
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DOFFLER 40CF59 LED TV dump file is shared below for repairing the firmware problem. DOFFLER 40CF59 LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the DOFFLER 40CF59 LED TV repairing.

DOFFLER 40CF59 LED TV Software download free.

How to Download Free Software for DOFFLER 40CF59 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done