TP.SIS231.P83

  • 22/01/2022
    0 32

    GOLDVISION LED32D3F LED TV FLASH DUMP

    Download Here

    GOLDVISION LED32D3F LED TV

    GOLDVISION LED32D3F LED TV flash dump file is shared for repairing purpose. If the GOLDVISION LED32D3F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the GOLDVISION LED32D3F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and GOLDVISION LED32D3F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the GOLDVISION LED32D3F LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    For writing flash dump file in GOLDVISION LED32D3F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given GOLDVISION LED32D3F LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications GOLDVISION LED32D3F LED TV:

    • Make/Brand: GOLDVISION
    • Main Board/Chassis: TP.SIS231.P83
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: GOLDVISION
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps TV

  • 22/01/2022
    0 34

    GOLDVISION LED28D3F LED TV FLASH DUMP

    Download Here

    GOLDVISION LED28D3F LED TV

    GOLDVISION LED28D3F LED TV flash dump file is shared for repairing purpose. If the GOLDVISION LED28D3F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the GOLDVISION LED28D3F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and GOLDVISION LED28D3F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the GOLDVISION LED28D3F LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    GOLDVISION LED28D3F

    For writing flash dump file in GOLDVISION LED28D3F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given GOLDVISION LED28D3F LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications GOLDVISION LED28D3F LED TV:

    • Make/Brand: GOLDVISION
    • Main Board/Chassis: TP.SIS231.P83
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: GOLDVISION
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps TV

  • 22/01/2022
    0 252

    GOLDVISION LED 32D2 TNT LED TV FLASH DUMP

    Download Here

    GOLDVISION LED 32D2 TNT LED TV

    GOLDVISION LED 32D2 TNT LED TV flash dump file is shared for repairing purpose. If the GOLDVISION LED 32D2 TNT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the GOLDVISION LED 32D2 TNT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and GOLDVISION LED 32D2 TNT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the GOLDVISION LED 32D2 TNT LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    GOLDVISION LED 32D2 TNT

    For writing flash dump file in GOLDVISION LED 32D2 TNT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given GOLDVISION LED 32D2 TNT LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications GOLDVISION LED 32D2 TNT LED TV:

    • Make/Brand: GOLDVISION
    • Main Board/Chassis: TP.SIS231.P83
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: GOLDVISION
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps TV

  • 22/01/2022
    0 21

    GOLDVISION GVLED28D3F LED TV FLASH DUMP

    Download Here

    GOLDVISION GVLED28D3F LED TV

    GOLDVISION GVLED28D3F LED TV flash dump file is shared for repairing purpose. If the GOLDVISION GVLED28D3F LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the GOLDVISION GVLED28D3F LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and GOLDVISION GVLED28D3F LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the GOLDVISION GVLED28D3F LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    GOLDVISION GVLED28D3F

    For writing flash dump file in GOLDVISION GVLED28D3F LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given GOLDVISION GVLED28D3F LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications GOLDVISION GVLED28D3F LED TV:

    • Make/Brand: GOLDVISION
    • Main Board/Chassis: TP.SIS231.P83
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: GOLDVISION
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps TV

  • 22/01/2022
    0 54

    GOLDVISION 42D1 TNT LED TV FLASH DUMP

    Download Here

    GOLDVISION 42D1 TNT LED TV

    GOLDVISION 42D1 TNT LED TV flash dump file is shared for repairing purpose. If the GOLDVISION 42D1 TNT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the GOLDVISION 42D1 TNT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and GOLDVISION 42D1 TNT LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the GOLDVISION 42D1 TNT LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    GOLDVISION 42D1 TNT

    For writing flash dump file in GOLDVISION 42D1 TNT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given GOLDVISION 42D1 TNT LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications GOLDVISION 42D1 TNT LED TV:

    • Make/Brand: GOLDVISION
    • Main Board/Chassis: TP.SIS231.P83
    • Board Type:
    • Power Source:
    • Rated Power Consumption:
    • Panel Info:
    • T-CON:
    • Screen Resolution:
    • Main Processor/Chipset:
    • SPI Flash:
    • Tuner:
    • Firmware Type: SPI Dump
    • Product User: GOLDVISION
    • Product Model:
    • Factory Code:

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps TV

  • 10/11/2021
    0 126

    FLASH DUMP UNITED LED32X11 LED TV

    Download Here

    UNITED LED32X11 LED TV

    UNITED LED32X11 LED TV flash dump file is shared for repairing purpose. If the UNITED LED32X11 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then flash dump file can be loaded. If the UNITED LED32X11 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply. If both are found ok and UNITED LED32X11 LED TV is still dead then check the primary power circuit if found ok then test the secondary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load flash dump file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and secondary voltage of the main board of the UNITED LED32X11 LED TV are tested and found accurate then write flash dump file, hope the issue will be resolved by rewriting flash memory.

    UNITED LED32X11 LED TV dump

    For writing flash dump file in UNITED LED32X11 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given UNITED LED32X11 LED TV flash dump and then verify after completion. if verifies successfully then resold it again and check. In some cases the flash dump file is saved from the same board but the remote control may not match. In such cases use universal remote control.

    Technical Specifications UNITED LED32X11 LED TV:

    • Make/Brand: UNITED
    • Main Board/Chassis: TP.SIS231.P83
    • Board Type: COMBO
    • Power Source: AC
    • Rated Power Consumption: 75W
    • Panel Info: HD
    • T-CON:
    • Screen Resolution: 1366X768
    • Main Processor/Chipset: SISEU231
    • SPI Flash: 25Q64
    • Tuner:
    • Firmware Type: SPI DUMP
    • Product User: UNITED
    • Product Model: LED32X11
    • Factory Code: Click To See 

    Special Note:

    The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Flash Dump File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

    DOWNLOAD LINK

    Click for more Flash Dumps TV

Previous page
error: Content is protected !!

Adblock Detected

Please Close Ad Blocker and Refresh The Page Download Start Automaticly