TP.MS3663S.PA671

18/12/2023
0 15

VEKTA LD-24F6015BT LED TV FLASH DUMP
Download Here

VEKTA LD-24F6015BT LED TV

VEKTA LD-24F6015BT LED TV Software file is shared for repairing purpose. If the VEKTA LD-24F6015BT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the VEKTA LD-24F6015BT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and VEKTA LD-24F6015BT LED TV is still dead then check the primary power circuit if found ok then test the sVEKTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sVEKTAdary voltage of the main board of the VEKTA LD-24F6015BT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in VEKTA LD-24F6015BT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VEKTA LD-24F6015BT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications VEKTA LD-24F6015BT LED TV:
- Make/Brand: VEKTA
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: VEKTA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

VEKTA LD-24F6015BT LED TV dump file is shared below for repairing the firmware problem. VEKTA LD-24F6015BT LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the VEKTA LD-24F6015BT LED TV repairing.

VEKTA LD-24F6015BT LED TV Software download free.

How to Download Free Software for VEKTA LD-24F6015BT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/12/2023
0 9

VEKTA LD-24SF6015BT LED TV FLASH DUMP
Download Here

VEKTA LD-24SF6015BT LED TV

VEKTA LD-24SF6015BT LED TV Software file is shared for repairing purpose. If the VEKTA LD-24SF6015BT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the VEKTA LD-24SF6015BT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and VEKTA LD-24SF6015BT LED TV is still dead then check the primary power circuit if found ok then test the sVEKTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sVEKTAdary voltage of the main board of the VEKTA LD-24SF6015BT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in VEKTA LD-24SF6015BT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given VEKTA LD-24SF6015BT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications VEKTA LD-24SF6015BT LED TV:
- Make/Brand: VEKTA
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: VEKTA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

VEKTA LD-24SF6015BT LED TV dump file is shared below for repairing the firmware problem. VEKTA LD-24SF6015BT LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the VEKTA LD-24SF6015BT LED TV repairing.

VEKTA LD-24SF6015BT LED TV Software download free.

How to Download Free Software for VEKTA LD-24SF6015BT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
17/11/2023
0 16

SHIVAKI STV-24LED22W LED TV FLASH DUMP
Download Here

SHIVAKI STV-24LED22W LED TV

SHIVAKI STV-24LED22W LED TV Software file is shared for repairing purpose. If the SHIVAKI STV-24LED22W LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SHIVAKI STV-24LED22W LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SHIVAKI STV-24LED22W LED TV is still dead then check the primary power circuit if found ok then test the sSHIVAKIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSHIVAKIdary voltage of the main board of the SHIVAKI STV-24LED22W LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SHIVAKI STV-24LED22W LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SHIVAKI STV-24LED22W LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SHIVAKI STV-24LED22W LED TV:
- Make/Brand: SHIVAKI
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SHIVAKI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SHIVAKI STV-24LED22W LED TV dump file is shared below for repairing the firmware problem. SHIVAKI STV-24LED22W LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the SHIVAKI STV-24LED22W LED TV repairing.

SHIVAKI STV-24LED22W LED TV Software download free.

How to Download Free Software for SHIVAKI STV-24LED22W LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
14/11/2023
0 19

SHIVAKI STV-20LED25 LED TV FLASH DUMP
Download Here

SHIVAKI STV-20LED25 LED TV

SHIVAKI STV-20LED25 LED TV Software file is shared for repairing purpose. If the SHIVAKI STV-20LED25 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the SHIVAKI STV-20LED25 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and SHIVAKI STV-20LED25 LED TV is still dead then check the primary power circuit if found ok then test the sSHIVAKIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sSHIVAKIdary voltage of the main board of the SHIVAKI STV-20LED25 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in SHIVAKI STV-20LED25 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given SHIVAKI STV-20LED25 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications SHIVAKI STV-20LED25 LED TV:
- Make/Brand: SHIVAKI
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: SHIVAKI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

SHIVAKI STV-20LED25 LED TV dump file is shared below for repairing the firmware problem. SHIVAKI STV-20LED25 LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the SHIVAKI STV-20LED25 LED TV repairing.

SHIVAKI STV-20LED25 LED TV Software download free.

How to Download Free Software for SHIVAKI STV-20LED25 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/10/2023
0 11

PRESTIGIO PTV244DN02Z LED TV FLASH DUMP
Download Here

PRESTIGIO PTV244DN02Z LED TV

PRESTIGIO PTV244DN02Z LED TV Software file is shared for repairing purpose. If the PRESTIGIO PTV244DN02Z LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the PRESTIGIO PTV244DN02Z LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and PRESTIGIO PTV244DN02Z LED TV is still dead then check the primary power circuit if found ok then test the sPRESTIGIOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPRESTIGIOdary voltage of the main board of the PRESTIGIO PTV244DN02Z LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in PRESTIGIO PTV244DN02Z LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given PRESTIGIO PTV244DN02Z LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications PRESTIGIO PTV244DN02Z LED TV:
- Make/Brand: PRESTIGIO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: PRESTIGIO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

PRESTIGIO PTV244DN02Z LED TV dump file is shared below for repairing the firmware problem. PRESTIGIO PTV244DN02Z LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the PRESTIGIO PTV244DN02Z LED TV repairing.

PRESTIGIO PTV244DN02Z LED TV Software download free.

How to Download Free Software for PRESTIGIO PTV244DN02Z LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/10/2023
0 89

PRESTIGIO PTV24DN01Z LED TV FLASH DUMP
Download Here

PRESTIGIO PTV24DN01Z LED TV

PRESTIGIO PTV24DN01Z LED TV Software file is shared for repairing purpose. If the PRESTIGIO PTV24DN01Z LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the PRESTIGIO PTV24DN01Z LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and PRESTIGIO PTV24DN01Z LED TV is still dead then check the primary power circuit if found ok then test the sPRESTIGIOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPRESTIGIOdary voltage of the main board of the PRESTIGIO PTV24DN01Z LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in PRESTIGIO PTV24DN01Z LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given PRESTIGIO PTV24DN01Z LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications PRESTIGIO PTV24DN01Z LED TV:
- Make/Brand: PRESTIGIO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: PRESTIGIO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

PRESTIGIO PTV24DN01Z LED TV dump file is shared below for repairing the firmware problem. PRESTIGIO PTV24DN01Z LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the PRESTIGIO PTV24DN01Z LED TV repairing.

PRESTIGIO PTV24DN01Z LED TV Software download free.

How to Download Free Software for PRESTIGIO PTV24DN01Z LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
15/10/2023
0 18

POLAR P22L33T2C LED TV FLASH DUMP
Download Here

POLAR P22L33T2C LED TV

POLAR P22L33T2C LED TV Software file is shared for repairing purpose. If the POLAR P22L33T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR P22L33T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR P22L33T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR P22L33T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR P22L33T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR P22L33T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR P22L33T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR P22L33T2C LED TV dump file is shared below for repairing the firmware problem. POLAR P22L33T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR P22L33T2C LED TV repairing.

POLAR P22L33T2C LED TV Software download free.

How to Download Free Software for POLAR P22L33T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
15/10/2023
0 12

POLAR P22L32T2C LED TV FLASH DUMP
Download Here

POLAR P22L32T2C LED TV

POLAR P22L32T2C LED TV Software file is shared for repairing purpose. If the POLAR P22L32T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR P22L32T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR P22L32T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR P22L32T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR P22L32T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR P22L32T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR P22L32T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR P22L32T2C LED TV dump file is shared below for repairing the firmware problem. POLAR P22L32T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR P22L32T2C LED TV repairing.

POLAR P22L32T2C LED TV Software download free.

How to Download Free Software for POLAR P22L32T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
15/10/2023
0 10

POLAR P22L31T2C LED TV FLASH DUMP
Download Here

POLAR P22L31T2C LED TV

POLAR P22L31T2C LED TV Software file is shared for repairing purpose. If the POLAR P22L31T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR P22L31T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR P22L31T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR P22L31T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR P22L31T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR P22L31T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR P22L31T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR P22L31T2C LED TV dump file is shared below for repairing the firmware problem. POLAR P22L31T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR P22L31T2C LED TV repairing.

POLAR P22L31T2C LED TV Software download free.

How to Download Free Software for POLAR P22L31T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
15/10/2023
0 16

POLAR P24L25T2C LED TV FLASH DUMP
Download Here

POLAR P24L25T2C LED TV

POLAR P24L25T2C LED TV Software file is shared for repairing purpose. If the POLAR P24L25T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR P24L25T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR P24L25T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR P24L25T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR P24L25T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR P24L25T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR P24L25T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR P24L25T2C LED TV dump file is shared below for repairing the firmware problem. POLAR P24L25T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR P24L25T2C LED TV repairing.

POLAR P24L25T2C LED TV Software download free.

How to Download Free Software for POLAR P24L25T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done