TP.MS3663S.PA671

15/10/2023
0 9

POLAR PC20LH11T2C LED TV FLASH DUMP
Download Here

POLAR PC20LH11T2C LED TV

POLAR PC20LH11T2C LED TV Software file is shared for repairing purpose. If the POLAR PC20LH11T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR PC20LH11T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR PC20LH11T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR PC20LH11T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR PC20LH11T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR PC20LH11T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR PC20LH11T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR PC20LH11T2C LED TV dump file is shared below for repairing the firmware problem. POLAR PC20LH11T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR PC20LH11T2C LED TV repairing.

POLAR PC20LH11T2C LED TV Software download free.

How to Download Free Software for POLAR PC20LH11T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
15/10/2023
0 43

POLAR P24L34T2C LED TV FLASH DUMP
Download Here

POLAR P24L34T2C LED TV

POLAR P24L34T2C LED TV Software file is shared for repairing purpose. If the POLAR P24L34T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR P24L34T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR P24L34T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR P24L34T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR P24L34T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR P24L34T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR P24L34T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR P24L34T2C LED TV dump file is shared below for repairing the firmware problem. POLAR P24L34T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR P24L34T2C LED TV repairing.

POLAR P24L34T2C LED TV Software download free.

How to Download Free Software for POLAR P24L34T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
15/10/2023
0 10

POLAR P22L21T2C LED TV FLASH DUMP
Download Here

POLAR P22L21T2C LED TV

POLAR P22L21T2C LED TV Software file is shared for repairing purpose. If the POLAR P22L21T2C LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the POLAR P22L21T2C LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and POLAR P22L21T2C LED TV is still dead then check the primary power circuit if found ok then test the sPOLARdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sPOLARdary voltage of the main board of the POLAR P22L21T2C LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in POLAR P22L21T2C LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given POLAR P22L21T2C LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications POLAR P22L21T2C LED TV:
- Make/Brand: POLAR
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: POLAR
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

POLAR P22L21T2C LED TV dump file is shared below for repairing the firmware problem. POLAR P22L21T2C LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the POLAR P22L21T2C LED TV repairing.

POLAR P22L21T2C LED TV Software download free.

How to Download Free Software for POLAR P22L21T2C LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
17/09/2023
0 13

MANTA 19LHN38L LED TV FLASH DUMP
Download Here

MANTA 19LHN38L LED TV

MANTA 19LHN38L LED TV Software file is shared for repairing purpose. If the MANTA 19LHN38L LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the MANTA 19LHN38L LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and MANTA 19LHN38L LED TV is still dead then check the primary power circuit if found ok then test the sMANTAdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sMANTAdary voltage of the main board of the MANTA 19LHN38L LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in MANTA 19LHN38L LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given MANTA 19LHN38L LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications MANTA 19LHN38L LED TV:
- Make/Brand: MANTA
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: MANTA
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

MANTA 19LHN38L LED TV dump file is shared below for repairing the firmware problem. MANTA 19LHN38L LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the MANTA 19LHN38L LED TV repairing.

MANTA 19LHN38L LED TV Software download free.

How to Download Free Software for MANTA 19LHN38L LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
04/09/2023
0 15

LIBERTON 24HE1HDT LED TV FLASH DUMP
Download Here

LIBERTON 24HE1HDT LED TV

LIBERTON 24HE1HDT LED TV Software file is shared for repairing purpose. If the LIBERTON 24HE1HDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the LIBERTON 24HE1HDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and LIBERTON 24HE1HDT LED TV is still dead then check the primary power circuit if found ok then test the sLIBERTONdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sLIBERTONdary voltage of the main board of the LIBERTON 24HE1HDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in LIBERTON 24HE1HDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given LIBERTON 24HE1HDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications LIBERTON 24HE1HDT LED TV:
- Make/Brand: LIBERTON
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: LIBERTON
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

LIBERTON 24HE1HDT LED TV dump file is shared below for repairing the firmware problem. LIBERTON 24HE1HDT LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the LIBERTON 24HE1HDT LED TV repairing.

LIBERTON 24HE1HDT LED TV Software download free.

How to Download Free Software for LIBERTON 24HE1HDT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
04/09/2023
0 12

LIBERTON 22HE1FHDT LED TV FLASH DUMP
Download Here

LIBERTON 22HE1FHDT LED TV

LIBERTON 22HE1FHDT LED TV Software file is shared for repairing purpose. If the LIBERTON 22HE1FHDT LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the LIBERTON 22HE1FHDT LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and LIBERTON 22HE1FHDT LED TV is still dead then check the primary power circuit if found ok then test the sLIBERTONdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sLIBERTONdary voltage of the main board of the LIBERTON 22HE1FHDT LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in LIBERTON 22HE1FHDT LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given LIBERTON 22HE1FHDT LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications LIBERTON 22HE1FHDT LED TV:
- Make/Brand: LIBERTON
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: LIBERTON
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

LIBERTON 22HE1FHDT LED TV dump file is shared below for repairing the firmware problem. LIBERTON 22HE1FHDT LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the LIBERTON 22HE1FHDT LED TV repairing.

LIBERTON 22HE1FHDT LED TV Software download free.

How to Download Free Software for LIBERTON 22HE1FHDT LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
26/07/2023
0 36

IRBIS 24S80HD401B LED TV FLASH DUMP
Download Here

IRBIS 24S80HD401B LED TV

IRBIS 24S80HD401B LED TV Software file is shared for repairing purpose. If the IRBIS 24S80HD401B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IRBIS 24S80HD401B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IRBIS 24S80HD401B LED TV is still dead then check the primary power circuit if found ok then test the sIRBISdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIRBISdary voltage of the main board of the IRBIS 24S80HD401B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IRBIS 24S80HD401B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IRBIS 24S80HD401B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IRBIS 24S80HD401B LED TV:
- Make/Brand: IRBIS
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IRBIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IRBIS 24S80HD401B LED TV dump file is shared below for repairing the firmware problem. IRBIS 24S80HD401B LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the IRBIS 24S80HD401B LED TV repairing.

IRBIS 24S80HD401B LED TV Software download free.

How to Download Free Software for IRBIS 24S80HD401B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
20/07/2023
0 17

ERGO LE24CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE24CT5000AK LED TV

ERGO LE24CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE24CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE24CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE24CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE24CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE24CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE24CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE24CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE24CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE24CT5000AK LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the ERGO LE24CT5000AK LED TV repairing.

ERGO LE24CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE24CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 16

ERGO LE24CT5000K LED TV FLASH DUMP
Download Here

ERGO LE24CT5000K LED TV

ERGO LE24CT5000K LED TV Software file is shared for repairing purpose. If the ERGO LE24CT5000K LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE24CT5000K LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE24CT5000K LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE24CT5000K LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE24CT5000K LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE24CT5000K LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE24CT5000K LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE24CT5000K LED TV dump file is shared below for repairing the firmware problem. ERGO LE24CT5000K LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the ERGO LE24CT5000K LED TV repairing.

ERGO LE24CT5000K LED TV Software download free.

How to Download Free Software for ERGO LE24CT5000K LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 14

ERGO LE21CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE21CT5000AK LED TV

ERGO LE21CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE21CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE21CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE21CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE21CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE21CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE21CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE21CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE21CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE21CT5000AK LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the ERGO LE21CT5000AK LED TV repairing.

ERGO LE21CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE21CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done