TP.VST59S.P89

30/10/2023
0 22

RUBIN RB-28D8 LED TV FLASH DUMP
RUBIN RB-28D8 LED TV

RUBIN RB-28D8 LED TV Software file is shared for repairing purpose. If the RUBIN RB-28D8 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the RUBIN RB-28D8 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and RUBIN RB-28D8 LED TV is still dead then check the primary power circuit if found ok then test the sRUBINdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sRUBINdary voltage of the main board of the RUBIN RB-28D8 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in RUBIN RB-28D8 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given RUBIN RB-28D8 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications RUBIN RB-28D8 LED TV:
- Make/Brand: RUBIN
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: RUBIN
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

RUBIN RB-28D8 LED TV dump file is shared below for repairing the firmware problem. RUBIN RB-28D8 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the RUBIN RB-28D8 LED TV repairing.

RUBIN RB-28D8 LED TV Software download free.

How to Download Free Software for RUBIN RB-28D8 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
30/10/2023
0 60

RUBIN RB-29D5 LED TV FLASH DUMP
RUBIN RB-29D5 LED TV

RUBIN RB-29D5 LED TV Software file is shared for repairing purpose. If the RUBIN RB-29D5 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the RUBIN RB-29D5 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and RUBIN RB-29D5 LED TV is still dead then check the primary power circuit if found ok then test the sRUBINdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sRUBINdary voltage of the main board of the RUBIN RB-29D5 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in RUBIN RB-29D5 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given RUBIN RB-29D5 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications RUBIN RB-29D5 LED TV:
- Make/Brand: RUBIN
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: RUBIN
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

RUBIN RB-29D5 LED TV dump file is shared below for repairing the firmware problem. RUBIN RB-29D5 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the RUBIN RB-29D5 LED TV repairing.

RUBIN RB-29D5 LED TV Software download free.

How to Download Free Software for RUBIN RB-29D5 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
24/10/2023
0 514

ROLSEN RL-28D1307 LED TV FLASH DUMP
ROLSEN RL-28D1307 LED TV

ROLSEN RL-28D1307 LED TV Software file is shared for repairing purpose. If the ROLSEN RL-28D1307 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ROLSEN RL-28D1307 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ROLSEN RL-28D1307 LED TV is still dead then check the primary power circuit if found ok then test the sROLSENdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sROLSENdary voltage of the main board of the ROLSEN RL-28D1307 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ROLSEN RL-28D1307 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ROLSEN RL-28D1307 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ROLSEN RL-28D1307 LED TV:
- Make/Brand: ROLSEN
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ROLSEN
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ROLSEN RL-28D1307 LED TV dump file is shared below for repairing the firmware problem. ROLSEN RL-28D1307 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the ROLSEN RL-28D1307 LED TV repairing.

ROLSEN RL-28D1307 LED TV Software download free.

How to Download Free Software for ROLSEN RL-28D1307 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/07/2023
0 2,243

IRBIS M28Q77HAL LED TV FLASH DUMP
IRBIS M28Q77HAL LED TV

IRBIS M28Q77HAL LED TV Software file is shared for repairing purpose. If the IRBIS M28Q77HAL LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IRBIS M28Q77HAL LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IRBIS M28Q77HAL LED TV is still dead then check the primary power circuit if found ok then test the sIRBISdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIRBISdary voltage of the main board of the IRBIS M28Q77HAL LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IRBIS M28Q77HAL LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IRBIS M28Q77HAL LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IRBIS M28Q77HAL LED TV:
- Make/Brand: IRBIS
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IRBIS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IRBIS M28Q77HAL LED TV dump file is shared below for repairing the firmware problem. IRBIS M28Q77HAL LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the IRBIS M28Q77HAL LED TV repairing.

IRBIS M28Q77HAL LED TV Software download free.

How to Download Free Software for IRBIS M28Q77HAL LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
10/07/2023
0 216

DNS H32A30 LED TV FLASH DUMP
DNS H32A30 LED TV

DNS H32A30 LED TV Software file is shared for repairing purpose. If the DNS H32A30 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DNS H32A30 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DNS H32A30 LED TV is still dead then check the primary power circuit if found ok then test the sDNSdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDNSdary voltage of the main board of the DNS H32A30 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DNS H32A30 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DNS H32A30 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DNS H32A30 LED TV:
- Make/Brand: DNS
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DNS
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DNS H32A30 LED TV dump file is shared below for repairing the firmware problem. DNS H32A30 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the DNS H32A30 LED TV repairing.

DNS H32A30 LED TV Software download free.

How to Download Free Software for DNS H32A30 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
26/06/2023
0 15

DEXP 32A3300 LED TV FLASH DUMP
DEXP 32A3300 LED TV

DEXP 32A3300 LED TV Software file is shared for repairing purpose. If the DEXP 32A3300 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DEXP 32A3300 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DEXP 32A3300 LED TV is still dead then check the primary power circuit if found ok then test the sDEXPdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDEXPdary voltage of the main board of the DEXP 32A3300 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DEXP 32A3300 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DEXP 32A3300 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DEXP 32A3300 LED TV:
- Make/Brand: DEXP
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DEXP
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DEXP 32A3300 LED TV dump file is shared below for repairing the firmware problem. DEXP 32A3300 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the DEXP 32A3300 LED TV repairing.

DEXP 32A3300 LED TV Software download free.

How to Download Free Software for DEXP 32A3300 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/06/2023
0 10

DIGITAL DLE-3216 LED TV FLASH DUMP
DIGITAL DLE-3216 LED TV

DIGITAL DLE-3216 LED TV Software file is shared for repairing purpose. If the DIGITAL DLE-3216 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DIGITAL DLE-3216 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DIGITAL DLE-3216 LED TV is still dead then check the primary power circuit if found ok then test the sDIGITALdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDIGITALdary voltage of the main board of the DIGITAL DLE-3216 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DIGITAL DLE-3216 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DIGITAL DLE-3216 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DIGITAL DLE-3216 LED TV:
- Make/Brand: DIGITAL
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DIGITAL
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DIGITAL DLE-3216 LED TV dump file is shared below for repairing the firmware problem. DIGITAL DLE-3216 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the DIGITAL DLE-3216 LED TV repairing.

DIGITAL DLE-3216 LED TV Software download free.

How to Download Free Software for DIGITAL DLE-3216 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/06/2023
0 113

DIGITAL DLE-3215 LED TV FLASH DUMP
DIGITAL DLE-3215 LED TV

DIGITAL DLE-3215 LED TV Software file is shared for repairing purpose. If the DIGITAL DLE-3215 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DIGITAL DLE-3215 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DIGITAL DLE-3215 LED TV is still dead then check the primary power circuit if found ok then test the sDIGITALdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDIGITALdary voltage of the main board of the DIGITAL DLE-3215 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DIGITAL DLE-3215 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DIGITAL DLE-3215 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DIGITAL DLE-3215 LED TV:
- Make/Brand: DIGITAL
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DIGITAL
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DIGITAL DLE-3215 LED TV dump file is shared below for repairing the firmware problem. DIGITAL DLE-3215 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the DIGITAL DLE-3215 LED TV repairing.

DIGITAL DLE-3215 LED TV Software download free.

How to Download Free Software for DIGITAL DLE-3215 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/06/2023
0 9

DIGITAL DLE-3917 LED TV FLASH DUMP
DIGITAL DLE-3917 LED TV

DIGITAL DLE-3917 LED TV Software file is shared for repairing purpose. If the DIGITAL DLE-3917 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DIGITAL DLE-3917 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DIGITAL DLE-3917 LED TV is still dead then check the primary power circuit if found ok then test the sDIGITALdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDIGITALdary voltage of the main board of the DIGITAL DLE-3917 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DIGITAL DLE-3917 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DIGITAL DLE-3917 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DIGITAL DLE-3917 LED TV:
- Make/Brand: DIGITAL
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DIGITAL
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DIGITAL DLE-3917 LED TV dump file is shared below for repairing the firmware problem. DIGITAL DLE-3917 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the DIGITAL DLE-3917 LED TV repairing.

DIGITAL DLE-3917 LED TV Software download free.

How to Download Free Software for DIGITAL DLE-3917 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
25/06/2023
0 15

DIGITAL DLE-3217 LED TV FLASH DUMP
DIGITAL DLE-3217 LED TV

DIGITAL DLE-3217 LED TV Software file is shared for repairing purpose. If the DIGITAL DLE-3217 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the DIGITAL DLE-3217 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and DIGITAL DLE-3217 LED TV is still dead then check the primary power circuit if found ok then test the sDIGITALdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sDIGITALdary voltage of the main board of the DIGITAL DLE-3217 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in DIGITAL DLE-3217 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given DIGITAL DLE-3217 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications DIGITAL DLE-3217 LED TV:
- Make/Brand: DIGITAL
- Main Board/Chassis: TP.VST59S.P89
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: DIGITAL
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

DIGITAL DLE-3217 LED TV dump file is shared below for repairing the firmware problem. DIGITAL DLE-3217 LED TV has the main board TP.VST59S.P89 installed in it so the SPI Flash file backup saved from working board TP.VST59S.P89. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.VST59S.P89 dump file is shared below for the DIGITAL DLE-3217 LED TV repairing.

DIGITAL DLE-3217 LED TV Software download free.

How to Download Free Software for DIGITAL DLE-3217 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done

RUBIN RB-28D8 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications RUBIN RB-28D8 LED TV:

About Mainboard:

RUBIN RB-29D5 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications RUBIN RB-29D5 LED TV:

About Mainboard:

ROLSEN RL-28D1307 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications ROLSEN RL-28D1307 LED TV:

About Mainboard:

IRBIS M28Q77HAL LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications IRBIS M28Q77HAL LED TV:

About Mainboard:

DNS H32A30 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DNS H32A30 LED TV:

About Mainboard:

DEXP 32A3300 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DEXP 32A3300 LED TV:

About Mainboard:

DIGITAL DLE-3216 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DIGITAL DLE-3216 LED TV:

About Mainboard:

DIGITAL DLE-3215 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DIGITAL DLE-3215 LED TV:

About Mainboard:

DIGITAL DLE-3917 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DIGITAL DLE-3917 LED TV:

About Mainboard:

DIGITAL DLE-3217 LED TV

Troubleshooting Guide:

Installation Instructions:

Technical Specifications DIGITAL DLE-3217 LED TV:

About Mainboard:

Adblock Detected